User manual KONICA BIZHUB 750

[. . . ] 750/600 User Manual x Introduction Introduction Thank you for choosing this machine. This manual contains details on the operation of the various functions of the machine, precautions on its use, and basic troubleshooting procedures. In order to ensure that this machine is used correctly and efficiently, carefully read this manual before using the machine. After reading the manual, store it in the designated holder so that it can easily be referred to when questions or problems arise during operation. [. . . ] (when PK-504/PK-505/ ZU-601/ZU-602 is installed on FS-504/FS602) If any message other than those listed above appears, perform the operation described in the message. If the problem is not corrected after the described operation is performed, contact your technical representative. 5-16 bizhub 750/600 Troubleshooting 5 5. 6 Main messages and their remedies Message Original left on glass. A document with a nonstandard size or with a size too small to be detected is loaded. A setting was selected that gives priority to the setting selected first. Since the maximum amount of copies for the indicated finisher exit tray has been exceeded, the machine is unable to make copies. Copies cannot be made unless a user name and its correct password are entered. Copies cannot be made unless an account name and its correct password are entered. Since a machine door or cover is open or an option is not installed correctly, the machine is unable to make copies. Either select paper of a different size or load paper of a suitable size. Input User Name and Password to login. Make copies using only one of the settings, for example, by canceling the setting selected first. Remove all copies from the indicated tray. Type in your user name and password. 2-36. ) Input Account Name and Password to login. Type in your account name and password. Close ) Section properly. Contact your administrator. Make sure that all doors and covers are closed and that all options are installed correctly. Replenish paper. Load paper into the indicated tray. Replace Staple Cartridge or cancel Staple mode. Replace the staple cartridge. Cause Since a paper misfeed occurred, the machine is unable to make copies. 5-7. ) Inform your technical representative of the code displayed on the touch panel. Malfunction detected. Please call your Technical Representative. If any message other than those listed above appears, perform the operation described in the message. If the problem is not corrected after the described operation is performed, contact your technical representative. 5-18 bizhub 750/600 6 Specifications Specifications 6 6 6. 1 Specifications Specifications bizhub 750/600 Specifications Type Document holder Photoconductor Luminous source Copying system Developing system Fusing system Resolution Document Console Stationary OPC Xenon lamp Laser electrostatic transfer method Dry-type dual-component reverse magnetic brush developing Heat roller 600 dpi × 600 dpi Types: Sheets, books (spreads), three-dimensional objects Size: Maximum A3 (11 × 17) Thickness: Maximum 30 mm; Weight: 6. 8 kg (three-dimensional objects) Normal paper (60 to 90 g/m2), thick paper (91 to 200 g/m2), thin paper (50 to 59 g/m2), User paper 1/2/3, recycled paper, colored paper, special paper, fine paper, label sheets*, letterheads, tab paper, overhead projector transparencies*, trace paper* *Can only be fed through the bypass tray Tray 1 and 2: A4 v, B5 v, A5 v, 8-1/2 × 11v, 5-1/2 × 8-1/2v, 16K v Tray 3 and 4: A3 w to A5 v, 11 × 17 w to 5-1/2 × 8-1/2v, 8-1/2 × 14 w, F4*1, 16K w/v, 8K v Width: 182 to 314 mm; Length: 139. 7 to 458 mm Bypass tray: A3 w to A6 w, 11 × 17 w to 5-1/2 × 8-1/2w/v, 8-1/2 × 14 w, F4*1, 16K w/v, 8K v Width: 100 to 314 mm; Length: 139. 7 to 458 mm Tray 1: Normal paper: 1, 500 sheets(80g/m2) Tray 2: Normal paper: 1, 000 sheets(80g/m2) Tray 3 and 4 (universal tray) Normal paper: 500 sheets(80g/m2) Bypass tray (universal tray): Normal paper: 100 sheets(80g/m2) bizhub 750: About 5 minutes bizhub 600: About 4 minutes and 30 seconds Paper types Paper sizes Paper tray capacity Warm-up time bizhub 750/600 6-3 6 Specifications Image loss Specifications Leading edge/trailing edge : Less than 1. 5 mm ± 1. 5 mm (front side), 2. 0 mm ± 2. 0 mm (back side); Front edge/Rear edge: Less then 1 mm ± 1 mm bizhub 750: 2. 9 seconds or less bizhub 600: 3. 3 seconds or less bizhub 750: 75 ppm (A4 v), 43 ppm (A3 w), 49 ppm (B4 w), 58 ppm (A4 w), 65 ppm (B5 w), 75 ppm (B5 v), 75 ppm (A5 v) bizhub 600: 60 ppm (A4 v), 35 ppm (A3 w), 40 ppm (B4 w), 47 ppm (A4 w), 52 ppm (B5 w), 60 ppm (B5 v), 60 ppm (A5 v) ×1. 0 (full size): ×1. 000 ± 1. 0% or less Enlarge: ×1. 154, ×1. 224, ×1. 414, ×2. 000 Reduce: ×0. 866, ×0. 816, ×0. 707, ×0. 500 Minimal: 0. 930 Zoom: ×0. 250 to ×4. 000 (in 0. 1% increments) Stored zoom ratios: 3 1 to 9, 999 sheets, 1 to 9, 999 sets Copy density: Automatic and manual adjustment (9 levels) Background density: Manual adjustment (9 levels) AC220-240V, 10A, 50Hz 75 bB or less (while operating) Maximum 2 KW or less (including options) 650 mm (W) × 791 mm (D) × 1, 140 mm (H) *2 First copy Copy speed Magnification ratios Multiple copies Density adjustment Power requirements Noise Power consumption Dimensions Space requirements Memory Weight 1, 275 mm (W) × 791 mm (D) 512 MB Approx. 222 kg *1 There are four F4 (Foolscap) sizes: 8-1/4 × 13 w, 8-1/8 × 13-1/4 w, 81/2 × 13 w and 8 × 13 w. For details, contact your technical representative. *2 The indicated spaced requirements represent the space required to fully extend the bypass tray. In order to incorporate improvements, these product specifications are subject to change without notice. 6-4 bizhub 750/600 Specifications ADF Specifications Document feed methods Normal paper: Single-sided and double-sided documents "Mixed Original" function: Combination of single-sided and double-sided documents Z-folded original: Single-sided document Tab paper: Single-sided document 50 to 200 g/m2 Single-sided/double-sided documents: A3 w to A5 w/v Mixed document sizes: Refer to Table 1. Maximum 100 sheets (80 g/m2) Supplied from main unit 625 mm (W) × 576 mm (D) × 154 mm (H) Approx. [. . . ] 4-20, 4-26 E Edit margin setting . . . . . . . . . . . . . . . . . 8-61 Emptying the dust boxes . . . . . . . 9-14 Energy Star . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x-3 Enlarge and reduce settings . . 3-39 Enlarge display key . . . . . . . . . . . . . . . . 2-17 Enlarge display timer setting . . 4-30 Enlarging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39 Entering text . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2 Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-75 Erase functions . . . . . . . . . . . . . . . . . . . . . . 8-74 Exit tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8 F Fax key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-52 Finisher FS-504 . . . . . . 2-7, 2-10, 6-7 Finisher FS-602 . . . . . . 2-8, 2-10, 6-8 Finishing settings . . . . . . . . . . . . . . . . . . . 3-65 K Key counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]