User manual KONICA BC-10

[. . . ] · Every effort has been made in the preparation of this manual to ensure the accuracy of its contents. However, should you have any questions or find any errors, please contact a KONICA MINOLTA SENSING-authorized service facility. · KONICA MINOLTA SENSING will not accept any responsibility for consequences arising from the use of the instrument. · Company names and product names which appear in this manual are their trademarks or registered trademarks. [. . . ] Connecting procedure is now complete Note Before turning ON the power to the computer, always turn ON the power to the VIVID 9i and wait until it is ready for operation (see page 21). 17 Connecting the VIVID 9i to a Computer Setting the SCSI ID No. In order for the computer to recognize that the VIVID 9i is connected to the computer via the SCSI interface, a SCSI ID No. 5 has been set as the default setting before shipment. Note If other devices are connected to the computer via the SCSI interface, make sure that the SCSI ID No. of the VIVID 9i differs from those set for the devices. [Setting Procedure] 1 2 Press . Press to locate the arrow cursor to "SCSI SETTINGS". STANDARD 3 HQ ON COLOR OFF W. B. SCSI DEFAULT 5 ENABLED NF ON WHITE BALANCE INITIAL MODE INITIAL CONDITION SCSI SETTINGS INFO 3 4 Press (or ). The SCSI SETTINGS view will appear. ENTER SELECT SCSI SETTINGS SCSI ID 5 ENABLED Press SI ID". to locate the arrow cursor to "SC- TERMINATE 5 6 7 Press (or ). will turn to pink. ENTER SELECT SCSI SETTINGS SCSI ID 6 ENABLED Press to select the desired SCSI ID No. TERMINATE <Settings> · 0 to 6: SCSI ID No. Press . Setting is now complete. ENTER Note To cancel the setting and return the SCSI SETTINGS screen to its original state, press . CANCEL 18 Connecting the VIVID 9i to a Computer Setting the Terminator The VIVID 9i has a built-in SCSI terminator. The terminator is required if the VIVID 9i is the last device of those connected in series to the SCSI interface (i. e. , if only one of the SCSI ports on the VIVID 9i is used). If the terminator is not set correctly, the VIVID 9i or devices connected to the SCSI interface may malfunction. Memo "ENABLED" has been selected as the default setting before shipment. Note "DISABLE" must be selected if the VIVID 9i is connected via the SCSI interface but is not the last device of those connected in series, and "ENABLE" must be selected if it is not connected via the SCSI interface. [Setting Procedure] 1 2 Press . Press to locate the arrow cursor to "SCSI SETTINGS". STANDARD 3 HQ ON COLOR OFF W. B. SCSI DEFAULT 5 ENABLED NF ON WHITE BALANCE INITIAL MODE INITIAL CONDITION SCSI SETTINGS INFO 3 4 Press (or ). For Field Calibration, refer to page 32. Relationship between Measurement Distance and Object Select the most suitable lens by referring to the table given below. Memo The closer the object to the VIVID 9i, the higher the measurement accuracy is. On the other hand, influences of shades produced due to roughness on the surface of the object can be reduced if the object is positioned far from the VIVID 9i. WIDE Lens Measurement Distance Horizontal Object Size Vertical 500 299 224 600 359 269 800 478 359 1000 598 449 2500 1495 1121 Unit (mm) MIDDLE Lens Measurement Distance Horizontal Object Size Vertical 500 165 124 600 198 148 800 263 198 1000 329 247 2500 823 618 Unit (mm) TELE Lens Measurement Distance Horizontal Object Size Vertical 500 93 69 600 111 83 800 148 111 1000 185 139 2500 463 347 Unit (mm) 28 Replacing the Lens and Field Calibration Replacing Procedure You can use the status information to see what type of lens is currently attached. The explanation below assume that the power to the digitizer is ON, but note that it is also possible to change the lens while the power is OFF. If the power is OFF, however, you cannot use the digitizer's viewfinder or control keys. Ref. Note For display of the status information, refer to page 44. · Only the lenses supplied as standard accessories with the VIVID 9i can be used. (They are not compatible with other VIVID models since they have been calibrated with the VIVID 9i only. ) · Since the VIVID 9i is a precision instrument, do not leave it without lens when replacing the lens. · Dust and scratches on the lens surface may adversely affect precision. · Dust or dirt on the lens mount surface may produce incorrect measurement data. In this case, wipe the lens mount surface with a clean, dry cloth and then blow it with a camera air blower etc. · Dust and dirt collected on the lens mount surface on the body side must also be removed with a camera air blower etc. · SCSI communication is not available while the lens is being replaced. [. . . ] Initial conditions that cannot be changed (as determined by the DIGITIZE scan mode) are not displayed. Use this feature when you want to remove the CCD offset components and get the signal components only. This setting is not shown if INITIAL MODE-COLOR is set to OFF. > If ON, log correction is applied to color data. This setting is not shown if INITIAL MODE-COLOR is set to OFF. LOG 46 Chapter 4 Appendix 47 Error Messages The following error messages appear if incorrect operation is performed or an abnormality occurs with the VIVID 9i. [. . . ]