User manual KOMPERNASS PARKSIDE PKGS 1450-KH 3118 CROSSCUT MITRE SAW

[. . . ] · Always check that the saw runs correctly under no load first. If there are any unusual noises or vibrations switch the saw off immediately and pull the plug out of the mains socket. Get it checked out at a specialist repair centre and repaired if necessary. · Bolt down the crosscut and mitre saw on to a steady surface using the holding down bolt holes provided in the base. [. . . ] Always switch off the power supply (pull out the plug) when you carry out adjustments or check the set-up of the machine. To make any necessary adjustment, follow this procedure: Move the saw table into the home position (0° - setting). Bring down the cutting head and compare the alignment of the side face of the saw blade with the left-hand edge of the saw notch on the table. Changing the setting ­ if required, is done by loosening the three bolts directly behind the saw blade (see Fig / ) with the Allen key (e) and moving the cutting arm so that it is parallel. Stop plate Check the stop plate particularly if it has been removed from the machine and replaced. Adjustment of the stop plate can only be carried out after the saw blade has been set parallel as above. Place one face of the set square against the stop plate and the other against the side face of the blade. If required, the adjustment is done as follows; Unscrew the two bolts at the rear of the stop plate and set the stop plate so that it is at 90° to the side face of the saw blade. Saw blade depth Check the saw blade depth with the cutting head lowered as far down as possible. Test that no teeth come into contact with any of the metal surfaces by turning the blade lightly by hand. If the blade does not turn freely, carry out the adjustment as follows: Unscrew the lock nut (see Fig. Mitre setting 0° If required you can adjust the 0° mitre stop setting. Move the saw table into the 90° home position (0° - setting) and with the cutting head lowered, compare the position of the side face of the saw blade with the table's support surface. / ) and turn the screw until it touches the casting and the saw blade is at 90° to the saw table. The saw blade must remain at right angles to the saw table and the scale reading on the cutting head remain at 0°. Mitre setting 45° If required you can adjust the 45° mitre stop setting. Unscrew the quick-set angle adjuster and tilt the cutting arm until it reaches the 45° setting on the scale. Use a combination angle gauge to compare the side face of the saw blade with the table's support surface. · /r) and turn the screw until it touches the casting and the saw blade is at 45° to the saw table. Adjust scale If necessary the scale pointer on the saw table can be readjusted. Just unscrew the bolt, move the pointer to the new position and retighten the bolt. Each line on the scale represents 1°. 6 www. kompernass. com +++ www. kompernass. com +++ www. kompernass. com +++ OPERATION Take note of the mains voltage. [. . . ] 21, D-44867 Bochum, Germany, hereby declare that this product conforms with the following EC regulations: Machinery Directive: EC low voltage regulations: Electromagnetic compatibility: Applicable harmonised standards: 98/37 EEC 73/23 EEC, 93/68 EEC 89/336 EEC EN 55014-1: 1993+A1+A2, EN 61000-3-2: 1995+A1+A2, EN 60555-3: 1987, EN 60555-3/A1: 1991, EN 55014-2: 1997 EN 61029-1: 1995, prEN 61029-2-9: 1994 PKGS 1450 CROSSCUT MITRE SAW Type: Bochum, 30. 06. 2003 Hans Kompernaß - Managing Director - 9 This piece of equipment is covered by a 3-year warranty as of the date of purchase. The equipment was produced with the greatest of care and underwent thorough testing before delivery. In the unlikely event of detecting a functional defect, please return the equipment in its original packaging with the proof of purchase to the closest service address. Damage caused due to improper handling as well as regular wear of the parts are not covered by this warranty. [. . . ]