User manual KODAK S510

[. . . ] 13 4 Troubleshooting and support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Picture frame problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Screen messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Digital frame specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2 Press to highlight Settings , then press OK. 3 Press to select a setting. 4 Press to exit. Settings menus Setting Options Upgrade firmware Upgrade firmware--load the latest version of firmware on your frame (page 12). This option is only displayed if the upgrade file Exit--return to the Home screen. (. img) is available on the frame (memory card, flash drive, etc. ). www. kodak. com/go/digitalframesupport 11 Changing frame settings Setting Viewing options Options Slide duration--specify how long each picture is displayed in a slide show, from 3 seconds (default) to 1 hour. Frame orientation--specify whether you wish to display your frame in landscape (default) or portrait orientation. Transitions--specify the transition style between pictures in a slide show. The picture fills the entire screen, some of the picture may be cut off (cropped). Press to adjust the screen brightness according to your lighting conditions. Check your frame model number and firmware version. Brightness Language About Upgrading your firmware Firmware is the software that runs on your frame. To check for the latest version, visit www. kodak. com/go/digitalframedownloads. Follow the screen directions to download the frame firmware and install it on your frame. IMPORTANT: Do not turn off the frame during the upgrade! 12 www. kodak. com/go/easysharecenter Changing frame settings Changing the frame orientation Your frame is set up to display pictures in landscape orientation portrait . You can turn it to Change the stand position: 1 Remove the stand, turn it 90 °, and replace as shown (see page 3). Change the setting: 1 Press Home , Settings . 2 Press to select Viewing options, then press OK. 3 Press to exit. www. kodak. com/go/digitalframesupport 13 4 Troubleshooting and support For step-by-step product support, visit www. kodak. com/go/digitalframesupport and select Interactive Troubleshooting & Repairs. Picture frame problems If. . . Try one or more of the following Press the power button on the remote control or on the frame (page 4). Make sure the power cable is securely connected (page 3). Make sure you are using the power cable that was included with your frame. Remote control does not Check the battery in the remote (page 2). Check the orientation of the card (page 5), then insert the card firmly into the slot. Do not expose this product to liquid, moisture, or extreme temperatures. The use of controls, adjustments, or procedures other than those specified herein may result in exposure to shock and/or electrical or mechanical hazards. The use of an accessory that is not recommended by Kodak may cause fire, electric shock, or injury. When removing the battery from the remote, allow it to cool; it may be hot. [. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed or used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) reorient or relocate the receiving antenna; 2) increase the separation between the equipment and the receiver; 3) connect the equipment to an outlet on a circuit different from that to which the receiver is connected; 4) consult the dealer or an experienced radio/TV technician for additional suggestions. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. [. . . ]