User manual KODAK ML-500

[. . . ] KODAK PROFESSIONAL ML-500 Digital Photo Print System Operator Guide EASTMAN KODAK COMPANY Kodak Professional Division Rochester, New York 14650 © Eastman Kodak Company, 2002. TM/MC/MR: Kodak, Kodak Professional, Ektatherm and Xtralife are trademarks www. kodak. com/go/professional P/N 2J7852 3/02 Safety and Regulatory Information Mechanical hazard; moving parts. Keep fingers, hands, hair, jewelry, and loose articles of clothing away from the path of the media through the printer. April 2002 iii Regulatory Approval Requirements Requirement Approval EMISSION 47CFR15 Class A (FCC) EN55022 Class A AS/NZS 3548 Class A ICES-003 Class A VCCI Class A BSMI CNS 13438) Class A IEC 61000-3-2, 3-3 IMMUNITY EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-11 iv April 2002 European Community Statement This equipment complies with the following European Directives: EMC Directive 89/336/EEC and amending Directives 92/31/EEC and 93/68/ EEC Low Voltage Directives 73/23/EEC. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. [. . . ] · To change the test print pattern, press SETUP >Configuration >Test Print > Pattern. PRINTING appears on the display panel while the image is printing. Installing the Software 1. Insert the CD shipped with the printer into the computer CD-ROM drive. Follow the on-screen instructions to install the software and view the documentation. 2-10 April 2002 3 Operating the Printer Operator Control Panel Overview 1 2 3 1. Buttons April 2002 3-1 Operating the Printer Display Messages The panel displays two lines of messages: · The printer state appears on the top line. There are two Indicators on the Operator Control Panel: STATUS and ERROR. Color Status Status and Error Indicator Indicator STATUS Green On, when the printer completes its self check. See Warnings, page 4-1. ERROR Red On, when service errors occur. If a service error message appears on the display, turn the Printer off and then back on. See Customer Support and Technical Assistance, page 4-8. 3-2 April 2002 Operating the Printer Buttons Button The following table describes the Operator Control Panel buttons. Printer State Function PRINT READY SETUP Makes a test print. Selects the currently displayed submenu or value when navigating through the SETUP menu. Exits the current submenu, return to the previous submenu, or exit the SETUP menu. CANCEL READY PRINTING SETUP SELECT READY SETUP SETUP READY SETUP April 2002 3-3 Operating the Printer Changing Printer Settings You can view and change printer settings using the printer's SETUP Mode. Press PRINT to scroll up (or CANCEL to scroll down) until CONFIGURATION is displayed on the top line and the languages are displayed on the bottom line. Press PRINT to scroll up (or CANCEL to scroll down) until the selected language is displayed on the bottom line. Repeatedly, press SETUP until the READY appears on the top line of the display. Submenu Options Menu SETUP Mode CONFIGURATION STATUS Test Print Language Version Logs User Logs Service Logs Pattern, Counts English, German, French, Spanish, Italian 3-4 April 2002 Operating the Printer Handling and Storing Prints Print image stability depends upon temperature, relative humidity, exposure, light intensity, and biological or chemical contaminants. Using KODAK PROFESSIONAL EKTATHERM XTRALIFE Ribbon increases the stability and durability of your prints. · Remove prints from the exit area ONLY AFTER the ML-500 printer ejects them. · Avoid storing prints at temperatures higher than 72°F (22°C) for extended periods. · Avoid exposure to sunlight. April 2002 3-5 4 Troubleshooting Error messages are displayed on the bottom line of the Operator Control Panel and indicate that a problem has occurred. Warnings and usercorrectable errors appear as messages, and service errors appear as numbers. Error Messages Warnings Message The STATUS indicator flashes while the ERROR indicator is off. Cause Solution PAPER LOW RIBBON LOW YELLOW LOW MAGENTA LOW CYAN LOW Approaching the end of the paper roll. When the printer stops printing, determine which ribbons are low and replace as needed. Wait for the printer to cool down, then continue with printing. XTRALIFE LOW XTRALIFE ribbon supply is low. COOLING The printer is too hot and is cooling down. April 2002 4-1 Troubleshooting User Correctable Errors Message The ERROR indicator flashes. Cause Solution PAPER EMPTY YELLOW EMPTY MAGENTA EMPTY CYAN EMPTY XTRALIFE EMPTY DOOR OPEN DRAWER REMOVED PAPER JAM Paper is empty. [. . . ] Dampen a lint-free cloth with distilled or deionized water, and wipe the cover. This eliminates dust build-up and prevents dirt from getting into the printer. Replacing the Air Filter 1. Replace the filter door using three thumbscrews. April 2002 5-1 Appendix A: Site Specifications Printer Specifications Printer Dimensions Width Depth Height Weight Acoustic: Maximum level 17 1/2 in. (55. 88 cm) 120 lbs (54. 4 kg) 70dB(A) April 2002 A-1 Site Specifications Space Requirements To provide access for media loading, and for service personnel, allow the following space around the printer. [. . . ]