User manual KODAK HR 500

[. . . ] KODAK PROFESSIONAL HR 500 Film Scanner P192_0016HC Operator's Guide Part No. 6B6377 P015 ©Eastman Kodak Company, 2000 - 2001 All rights reserved. Contents of this publication may not be reproduced in any form without permission from Eastman Kodak Company. Unpacking Instructions for the KODAK PROFESSIONAL HR 500 Film Scanner CAUTION: The HR 500 Film Scanner weighs almost 120 lbs (54, 5 kg). Be sure the table for the scanner: · is stable · can support approximately 120 lbs (54, 5 kg) · is at least 30 in. [. . . ] Reinstall the lamp cover, tighten the thumbscrews, and select a filter position. Calibrate the scanner (see Calibrating the Scanner on page 3-4). August 2001 4-7 Maintaining the Equipment Replacing the (Square) IR Filter IMPORTANT: The IR filter is made of glass and is expensive to replace. Use care when handling the IR filter. Wear white cotton gloves for this procedure. It is not necessary to power down the scanner before changing the IR filter. Open the lamp-and-filter-access door (see page 4-6 for the location of the lamp-and-filter-access door). NE S G PO IR filter (under balancefilter assembly) red handle 2. Loosen the thumbscrews on the lamp cover and pull the cover straight out. When you remove the cover, the safety switch is released, removing power to the lamp socket. CAUTION: Wait at least five minutes for the lamp to cool. 4-8 August 2001 Maintaining the Equipment 3. Position the red balance-filter selection handle of the balance-filter assembly in the center. Hold the red handle and pull the assembly straight out from the scanner. Clean the IR filter with the camel's-hair brush or, if needed, replace the IR filter as described in step 7. If replacing the IR filter, set the new filter in place with the arrows on the edges of the filter pointing down toward the scan lamp. Install the filter assembly in the scanner with the balance-filter selection handle in the middle. Reinstall the lamp cover, tighten the thumbscrews, and select a filter position. Calibrate the scanner (see Calibrating the Scanner on page 3-4). August 2001 4-9 Maintaining the Equipment 4-10 August 2001 Appendix A: Using the Service and Assembly Module (SAM) The Service and Assembly Module (SAM) software performs many of the same functions as other host software. Its primary purpose for users is to validate that your scanner is working correctly and to allow you to perform simple scan functions. There are also service and diagnostics functions that should be used only with the assistance of a Kodak service representative. Functions supported by the SAM software are: · setting a magnification · calibrating the scanner · setting the image processing mode (negative or positive) · autofocusing at any given magnification · defining the area to be scanned · scanning and transferring images from the scanner to the host computer · performing miscellaneous features such as: ­ turning the lamp on and off ­ resetting the lamp-on timer ­ rebooting the scanner ­ retrieving scanner usage information ­ displaying software version information · backing up and restoring critical scanner files A-1 Using the Service and Assembly Module (SAM) Installing the Service and Assembly Module (SAM) Software 1. Respond to the prompts in the installation program. You must provide the program location and the name of the program menu item. 4. Remove the CD and store it in a safe place. Backing Up Scanner Files IMPORTANT: It is essential that you back up the scanner files before using SAM. Click Backup to back up the critical scanner files. A-2 August 2001 Using the Service and Assembly Module (SAM) Using the Operations Controls If the Operations window does not appear, select View->Operations Controls. IMPORTANT: The Diagnostics, Sensors, Drives, and Transfer tabs are not needed for user functions. Use these tabs only at the request of your Kodak support representative. August 2001 A-3 Using the Service and Assembly Module (SAM) Performing the Functions on the Mag/Focus Tab IMPORTANT: Magnification Calibration should be done only with the guidance of a Kodak support representative. From the Operations window, click the Mag/Focus tab when you need to set the magnification (position of the lens) or do an autofocus. A-4 August 2001 Using the Service and Assembly Module (SAM) Setting the Magnification 1. The value can be between 0. 5 and 2. 0. The scanner's software maintains an internal Mag/Focus position table that associates a motor position for each of the possible magnification values. 2. Click Do Magnification. The lens and CCD move to the chosen position. Performing an Autofocus 1. The Range is the initial range of travel used for the CCD and lens, in motor steps. NOTE: To make the focus procedure faster: if you have focused on a given magnification, you can set the Range value to be less than 300. [. . . ] NOTE: It is not necessary to completely unthread the film. D-38 August 2001 Using the Long Roll Accessory Cleaning the Punch Readers 1. Locate the two punch readers, below the pressure rollers and adjacent to the left and right edges of the aperture. P192_1569BCA P192_1569BC two film readers punch readers 2. Use canned air to clean the left and right punch readers. August 2001 D-39 Using the Long Roll Accessory Cleaning the Rollers 1. On the Film Controls window, click Clean Rollers. D-40 August 2001 Using the Long Roll Accessory A dialog box appears. 3. [. . . ]