User manual KODAK DC200

[. . . ] KODAK DIGITAL SCIENCETM DC210 Plus Zoom/DC200 Cameras User's Guide for the cameras, KODAK Installation Software, KODAK DC200/DC210 Mounter Software, and KODAK Acquire/TWAIN Software. Visit Kodak on the World Wide Web at www. kodak. com ©Eastman Kodak Company, 1998 Kodak, Digital Science, FlashPix, Photolife, and the ds monogram are trademarks of Eastman Kodak Company. The FlashPix format is defined in a specification and test suite developed and published by Kodak in collaboration with Microsoft, Hewlett-Packard, and Live Picture. Only products that meet the specification and pass the test suite may use the FlashPix name and logo. Table of Contents Table of Contents Chapter-Page Table of Contents . warranty4 iv 1 Getting Started Congratulations on your purchase of the new KODAK DIGITAL SCIENCETM DC210 Plus Zoom (DC210) or KODAK DIGITAL SCIENCETM DC200 Camera (DC200). The DC200 camera features: built-in flash with red-eye reduction an easy to use status display of camera settings removable memory card video out capabilities which allow you to connect and run a slide show on your TV color LCD to immediately see or preview your pictures software to easily transfer pictures from the camera to your computer a mode dial to activate one of four different functions on the camera: Capture--takes, previews, or deletes a picture and adjusts the exposure Review--review or delete pictures Preference--adjust camera settings Connect--camera communicates with your computer The DC210 has all of the features of the DC200 plus: infrared remote connection to compatible devices 2X zoom lens (29 to 58mm) to zoom in on subjects and a close up option to set the focus at 8in. [. . . ] When a memory card is formatted it erases everything, including any templates on the card, and sets up new directories and pointers on the memory card. 2 Turn on the camera. The LCD displays the Preferences screen. 3 Press a / button until the Format Memory Card icon is highlighted on the third Preferences screen. The LCD displays the main Format Memory Card screen. 4 Press the DO-IT button. 5 Press a / button until CONTINUE FORMAT is highlighted. The card is formatted and the main Preferences screen reappears. 6 Press the DO-IT button. To cancel format: press a / button until CANCEL FORMAT is highlighted and then press the DO-IT button. The card is not formatted and the main Preferences screen reappears. 4-10 Video Out The Video Out screen is used to set the camera's video output format to NTSC or PAL. To set the video out format: 4 Preferences 1 Set the Mode dial to Preferences. 2 Turn on the camera. The LCD displays the Preferences screen. 3 Press a / button until the Video Out icon is highlighted on the third Preferences screen. The LCD displays the main Video Out screen. The current setting is checked (ü). 4 Press the DO-IT button. 5 Press a / button until the appropriate option is highlighted. The main Preferences screen reappears. 6 Press the DO-IT button. To reset: the Video Out setting is maintained until another setting is selected. This setting does not change when the camera is turned off. 4-11 Language The Language screen is used to select a language interface for the camera. When a specific language is selected, the LCD screens on the back of the camera will change to reflect the language selected. 2 Turn the camera on. The LCD displays the Preferences screen. 3 Press a / button until the Language icon is highlighted on the third Preference screen. The LCD displays the main Language screen. The current setting is checked (ü). 4 Press the DO-IT button. 5 Press a / button until the appropriate language is highlighted. The main Preferences screen reappears. 6 Press the DO-IT button. To change Language: press a / button until another language is highlighted and then press the DO-IT button. This setting does not change when the camera is turned off. 4-12 About The About screen is a view only screen that keeps a record of the camera's use. While viewing the About screen, you can look-up the following information: firmware version total number of pictures taken over the lifetime of the camera total number of flashes fired over the lifetime of the camera To view the About screen: 4 Preferences 1 Set the Mode dial to Preferences. 2 Turn the camera on. The LCD displays the Preferences screen. 3 Press a / button until the About icon is highlighted on the third Preferences screen. The LCD displays the About screen 4 Press the DO-IT button. 5 Press the DO-IT button to return to the main Preferences screen. 4-13 5 Installation Software 5 Installation KODAK Installation Software (Installation software) quickly and easily installs the software included on the DC200/DC210 CD to your computer. WINDOWS System Requirements WINDOWS 95, WINDOWS 98, or WINDOW NT System Software Personal computer with 486/66MHz microprocessor minimum, PENTIUM Processor recommended 8 MB or more of RAM available, 16 MB recommended available serial port and CD-ROM drive Installing the Software While the Installation software is automatically loading your software, take a few minutes to fill out and send in the DC200/DC210 product registration card. This allows you to receive information regarding software updates and registers some of the products included with the camera. Close all other applications before starting the Installation software. 1 Place the DC200/DC210 CD into your CD-ROM drive. If Auto Run is turned on in WINDOWS 95, WINDOWS 98, or WINDOWS NT, the first install window automatically appears. If the first install window does not automatically appear proceed to step 2. 2 Choose Run from the Start menu. 3 Type the path to the drive that contains the CD and then type \setup. exe For example: d:\setup. exe 5-1 The install window appears. 4 Select the language you want to install. 6 Read the agreement and click on the YES button to accept the software license agreement. If you do not accept the license you will not be able to install the software. 7 Select which software you wish to install and click on the NEXT button. 8 Select the name of the Program Folder and click on the NEXT button. If necessary, type a new folder name or select from the Existing Folders list. 5-2 9 Verify the settings and then click on the NEXT button. A progress screen appears while the software is installed. 10Select the preferred restart option and click on the FINISH button. 5 Installation If you have installed the KODAK DC200/ DC210 Mounter Software you must restart your computer. You are now ready to run the newly installed software. Detailed information on KODAK DC200/DC210 Mounter Software (chapter 7) and TWAIN Software (chapter 8) are included in this user manual. Instruction manuals for the additional software packages that were installed are included in the camera package. [. . . ] THIS WARRANTY BECOMES NULL AND VOID IF YOU FAIL TO PACK YOUR DC200/DC210 CAMERA IN A MANNER CONSISTENT WITH THE ORIGINAL PRODUCT PACKAGING AND DAMAGE OCCURS DURING PRODUCT SHIPMENT. THIS WARRANTY DOES NOT COVER: CIRCUMSTANCES BEYOND KODAK'S CONTROL; SERVICE OR PARTS TO CORRECT PROBLEMS RESULTING FROM THE USE OF ATTACHMENTS, ACCESSORIES OR ALTERATIONS NOT MARKETED BY KODAK; SERVICE REQUIRED AS THE RESULT OF UNAUTHORIZED MODIFICATIONS OR SERVICE; MISUSE, ABUSE; FAILURE TO FOLLOW KODAK'S OPERATING, MAINTENANCE OR REPACKAGING INSTRUCTIONS; OR FAILURE TO USE ITEMS SUPPLIED BY KODAK (SUCH AS ADAPTERS AND CABLES). KODAK MAKES NO OTHER WARRANTIES, EXPRESS, IMPLIED, OR OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE FOR THIS EQUIPMENT OR SOFTWARE. REPAIR OR REPLACEMENT WITHOUT CHARGE ARE KODAK'S ONLY OBLIGATION UNDER THIS WARRANTY. [. . . ]