User manual KODAK CAROUSEL NEW LOOK PROJECTOR

[. . . ] SM5440-1 18NOV97 Supersedes SM5440-1 13MAY97 Kodak Home Page on Internet SERVICE MANUAL for the Kodak Carousel NEW LOOK PROJECTORS Standard and Long Life Models 4200, 4200-J, 4200-KK, 4400, 4600, 4600-KK, 5600, 5600-J, and 5600-KK Intranet Table of Contents © Eastman Kodak Company, 1999 A100_0029HA PLEASE NOTE The information contained herein is based on the experience and knowledge relating to the subject matter gained by Eastman Kodak Company prior to publication. Eastman Kodak Company reserves the right to change this information without notice, and makes no warranty, express or implied, with respect to this information. Kodak shall not be liable for any loss or damage, including consequential or special damages, resulting from any use of this information, even if loss or damage is caused by Kodak's negligence or other fault. This equipment includes parts and assemblies sensitive to damage from electrostatic discharge. [. . . ] The SLIDE LIFT LEVER should make contact with the low surface of the SLIDE LIFT LEVER GAUGE TL-3001; the SLIDE LIFT LEVER should not make contact with the high surface of the SLIDE LIFT LEVER GAUGE TL-3001. [6] Bend the SLIDE LIFT LEVER until the adjustment is correct. SLIDE LIFT LEVER GUAGE TL-3001 SLIDE LIFT LEVER SELECT LEVER (not shown) A091_0016BCA A091_0016BA Adjustment Specification Use MECHANISM RUNNING FIXTURE. The LEVER should not make contact with the high surface of TL-3001. Adjusting the SLIDE LIFT LEVER POWER with Mechanism Out Warning Dangerous Voltage [1] Disconnect the main power. [3] Place the MECHANISM ASSEMBLY on the MECHANISM RUNNING FIXTURE TL-3000. [5] Press and hold the SELECT LEVER down to move the SLIDE LIFT LEVER to the highest position. The SLIDE LIFT LEVER should make contact with the low surface of the SLIDE LIFT LEVER GAUGE TL-3001; the SLIDE LIFT LEVER should not make contact with the high surface of the SLIDE LIFT LEVER GAUGE TL-3001. [7] Bend the SLIDE LIFT LEVER until the adjustment is correct. SM5440-1 ­ 18NOV97 27 SERVICE MANUAL SLIDE LIFT LEVER GUAGE TL-3001 SLIDE LIFT LEVER SELECT LEVER (not shown) A091_0016BCA A091_0016BA Adjusting the Focus Light Path - Auto Focus Models Adjustment Specification Seat AUTO-FOCUS TARGET SLIDE TL-3002 on the GATE MECHANISM. Use TL-3005 or TL-1165 to bend the AUTO-FOCUS BRACKET ASSEMBLY MIRROR until the image is within the target of the TARGET SLIDE. Warning Dangerous Voltage [1] Disconnect the main power. [3] Do the removal for the LOWER HOUSING ASSEMBLY. Important It is necessary to make a FAN COVER TOOL. [7] Install the AUTO-FOCUS TARGET SLIDE TL-3002 until it is fully seated in the GATE MECHANISM. [8] Look through the PROJECTION LENS hole and observe the focus light path on the AUTO-FOCUS TARGET SLIDE TL-3002. [9] Check the position of the image on the AUTO-FOCUS TARGET SLIDE TL-3002. 28 18NOV97 ­ SM5440-1 Adjustments [10] Bend the AUTO-FOCUS BRACKET ASSEMBLY MIRROR until the image is within the target on the TARGET SLIDE. Use ADJUSTMENT TOOL TL-3005 or the SPRING HOOK TL-1165. ADJUSTMENT TOOL TL-3005 or SPRING HOOK TL-1165 AUTO FOCUS BRACKET ASSEMBLY light path image AUTO-FOCUS TARGET SLIDE TL-3002 A091_4026HCA A091_4026HA Adjustment Specification Use TL-3002 to observe the focus light path and check the light image. Use T-BAR TL-3003 to bend the PHOTOCELL BRACKET to move the NULL in the center if necessary. Adjusting the NULL Warning Dangerous Voltage [1] Disconnect the main power. [2] Do the removal for the LOWER HOUSING ASSEMBLY. Important It is necessary to make a FAN COVER TOOL. [6] Install and hold the AUTO FOCUS TARGET SLIDE TL-3002 until it is fully seated in the GATE MECHANISM. [7] Look through the PROJECTION LENS hole and observe the focus light path on the AUTO-FOCUS TARGET SLIDE TL-3002. [8] Check that the TAB on the CLAMP PAD ASSEMBLY is in the NULL position. If the TAB is not in the correct position, do the adjustment procedure for the NULL. [9] Bend the PHOTOCELL BRACKET to move the NULL in the center; use T-BAR TL-3003. SM5440-1 ­ 18NOV97 29 SERVICE MANUAL Important If you cannot obtain the NULL position after doing the adjustment approximately 3 times, go to the adjustment procedure for the PHOTOCELL. light path T-BAR TL-3003 NULL position PROJECTION LENS TAB A091_4031BCA A091_4031BA AUTO-FOCUS TARGET SLIDE TL-3002 CLAMP LEVER PAD Adjustment Specification Use TL-3002 and FAN CAP 232729 to check the adjustment of the PHOTOCELL. Adjusting the PHOTOCELL PHOTOCELL CIRCUIT BOARD wratten FILTER (2) Warning Dangerous Voltage [1] Disconnect the main power. [2] Do the removal for the LOWER HOUSING ASSEMBLY. Important It is necessary to make a FAN COVER TOOL. See the Tools section. POST (2) PHOTOCELL HOUSING PHOTOCELL MASK A091_4032GCA A091_4032GA 30 18NOV97 ­ SM5440-1 Adjustments Warning Dangerous Voltage [4] Energize the projector. [. . . ] If the height is not correct, do the adjustment for the MANUAL and POWER SLIDE LIFT LEVER ECCENTRICS. SLIDE TRAY does not advance smoothly. SLIDE TRAY advances when "REVERSE" is pressed. SLIDE TRAY does not rotate freely when the SELECT BUTTON is pressed down. The projector has power. SM5440-1 ­ 18NOV97 47 SERVICE MANUAL Malfunction TIMER does not operate Check 1. Check the VARIABLE RESISTOR for correct operation and install a new part if necessary. Move the TIMER BUTTON forward and backward; use a DVM to check for changes in W. [. . . ]