User manual KLIPSCH LIGHTSPEAKER 5

[. . . ] WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. AVERTISSEMENT: Pour réduire le risque d'incendie ou de choc électrique, ne pas exposer cet appareil sous la pluie et l'humidité. 2 Tech Support: 1-800-KLIPSCH IMPORTANT SAFETY INSTRUCTIONS 1. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] If your LightSpeaker® 5 does not fit either because the trim ring/reflector opening is too small or the lighting fixture is not set deep enough, please go to www. klipsch. Choose your trim ring based on either A or B below and place the LightSpeaker® 5 trim ring over the back of the LightSpeaker® 5. Upon completion of the install, this trim ring should fit snuggly and uniformly to the ceiling and should also seat properly around the entire edge of your LightSpeaker® 5. A) The thicker trim ring will be used when your LightSpeaker® 5 is installed into a 6" lighting fixture. 10 Tech Support: 1-800-KLIPSCH B) The thinner one is used when installed into a 5" fixture. As long as the trim ring covers the edges of the lighting fixture and any rough drywall edges you may use either trim ring; it will not affect the performance of your LightSpeaker® 5. The three SimpleTabsTM, on the back of the speaker can be rotated outward and when the LightSpeaker® 5 is pressed into the housing, hold it centered and securely in place. SimpleTabsTM You will now adjust the Simple TabsTM on the back of the LightSpeaker® 5 to either A (6" recessed light fixture) or B (5" recessed light fixture). If you are installing into a 5" recessed lighting fixture, rotate each of the SimpleTabsTM out to position "B" on the top of the LightSpeaker® 5 unit. 11 Tech Support: 1-800-KLIPSCH If you are installing into a 6" recessed lighting fixture, rotate each of the SimpleTabsTM out to position "A" on the top of the LightSpeaker® 5 unit. SimpleTabsTM Step 6: Setting the Zone and L/R Stereo Switches. A) Set the zone switch on the back of the LightSpeaker® 5 to one, unless you are setting up a two zone system. For more on zones see Complete System Manual or go to www. Klipsch. com. 12 Tech Support: 1-800-KLIPSCH B) Set the left/right stereo switch. "L" if it is the left speaker, "R" if it is the right speaker. For additional information see Selecting LightSpeaker® 5 Locations on page 16. C) Your LightSpeaker® 5 system allows you to install up to 4 pair of (or 8 total ) speakers. If you are installing more than one pair of LightSpeakers® 5 you will probably want to divide your home into zones. Step 7: Installing your LightSpeaker® 5 into the recessed light fixture: A) Easiest Install: If you skipped steps 4 and 5, and your LightSpeaker® 5 fits with no modifications, screw it into the lighting fixture. 3) When the lens pops up, gently pry it away from the housing, being gentle and making sure not to break the tabs. 15 Tech Support: 1-800-KLIPSCH B) Removal of the lens AFTER your LightSpeaker® 5 has been installed. 1) There are three small indentations around the lens; with a small tip common screwdriver, nail file, paper clip or similar object, gently slip the tip into the indentation and pry the lens outward until the retaining tabs pull free. 2) To re-install the lens, align the tabs and the hole for the pairing LED, then push gently until the locking tabs snap into place. CAUTION: Do not touch the LED or Speaker Baffle with the lens off when the unit is hot, allow the unit to cool down before touching the baffle. 16 Tech Support: 1-800-KLIPSCH Selecting LightSpeaker® 5 Locations Survey your home to determine the location of 5" and 6" recessed lighting fixtures. As long as these are wired to the home's electricity through a common light switch, they should work perfectly. If you have multiple locations within one room, try to space the speakers as far as part as possible, this will provide the best stereo image and the best sound. In general, the maximum spacing of the speakers is determined by ceiling height. Using the table below, try to space speakers at the distances stated to or closer together. If you cannot place them closer than the recommended maximum spacing, do not worry, your sound quality will still be good. [. . . ] To obtain any applicable warranty service, please contact the dealer from which you purchased this product, or the distributor that supplied this product. Questions?We're waiting to hear from you! 1-800-KLIPSCH Email us! If you prefer, your questions and comments can be submitted by email, too; you can count on rapid response and clear, concise answers. support@klipsch. com WRITE THE PART NUMBER AND SERIAL NUMBER FROM YOUR PRODUCT BOX HERE AND RETAIN FOR PRODUCT REGISTRATION Part Number:______________________________________________ Serial Number:_____________________________________________ 22 Register your product online at www. klipsch. com/register. Tech Support: 1-800-KLIPSCH THIS DEVICE COMPLIES WITH FCC RULES PART 15. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) This device must accept any interference received including that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]