User manual KLIPSCH KG 3

[. . . ] The lamp holder of apparatus should not be obstructed OR should be easily accessed during intended use. To completely disconnect the power input, the lamp holder of the apparatus shall be disconnected from the mains. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Added weight of the device may cause instability of a free-standing portable lamp. [. . . ] The wireless transmitter can be centrally located which will provide audio and, together with the remote, allow you to control your LightSpeakers® from anywhere in your home To expand your system, additional LightSpeakers® or wireless RockSpeakers are available at www. klipsch. com. This incredible patented system provides even greater flexibility to you as the owner; since you can take this system with you if you move; and when you do, it leaves no trace (holes that need to be covered) that the system was ever installed and used. 7 Tech Support: 1-800-KLIPSCH Take just a minute to be sure you have everything you need to install your additional wireless distributed audio LightSpeaker® 5 from Klipsch®. Large & Small Trim Rings Lens LightSpeaker® 5 Note: The LightSpeaker® 5 is an add on unit to an existing LightSpeaker® System. You need a LightSpeaker® Transmitter to supply audio and control the lights on this unit. The Transmitter and Remote discussed in the manual are sold separately. 8 Tech Support: 1-800-KLIPSCH Instruction Manual Step 1: Decide which light will be replaced with LightSpeaker® 5. Your Klipsch® LightSpeaker® 5 has been specifically designed to cover large areas, however if the location of your fixtures allow you to do so, you should think about how you use your room and where you are likely to spend most of your time. Then choose the fixtures that are most evenly spaced to your preferred listening position. Turn off circuit breakers to all lighting fixtures you are working on!A) Turn off the circuit breaker and light switch, to the bulb you intend to replace with a LightSpeaker® 5. Your Klipsch® LightSpeaker® 5 is designed to fit into a standard Edison connector. Check your connector! 9 Tech Support: 1-800-KLIPSCH Step 3: Test fit your LightSpeaker® 5. Your LightSpeaker® 5 is designed to fit directly into most 5" (R30) and 6" (R40) down light cans by simply removing the existing light and, in the same manner as a light bulb, re-installing your LightSpeaker® 5 in its place. 1) While holding the LightSpeaker® 5 in the palm of your hand rotate the unit until one of the holding tabs is facing up. 2) Using a common screwdriver or other small flat object, gently push down and then out on the tab, easing it out through the opening in the LightSpeaker® 5 housing. Digital Amplifier & Switch Mode Power Supply · The E26 standard Edison Screw allows the unit to attach to any standard light fixture socket. · The high efficiency switch mode power supply delivers power to the LED and the digital amplifier without generating a lot of heat. · 20W high performance low distortion digital amplifier provides energy efficient sound · The on-board Digital Signal Processing delivers customized audio to each LightSpeaker® giving big speaker sound in a small speaker. 18 Tech Support: 1-800-KLIPSCH Loud Speaker · 2. 5" high performance custom engineered woofer with Micro Cellulose Polymer treated cone material provides even coverage and smooth natural sounding audio reproduction · Integrated high frequency disperser. Accessories · Optional flange allows LightSpeaker® to fit into either 5" (R30) or 6" (R40) recessed lighting fixtures. · Frosted Lens is acoustically transparent 5" LightSpeaker® Specifications Woofer 2. 5" Micro Cellulose Light Brightness 10W LED Wireless Reception 2. 4 GHz proprietary signal Frequency Response (+/- 3 dB) 90 Hz - 20 kHz Amplifier Power 20W Max SPL 93 dB SPL Dimensions LightSpeaker® depth (w/out Edison Screw) 5. 3" (135. 3 mm) LightSpeaker® diameter (without Flange) 5. 1" (130. 0 mm) LightSpeaker® diameter (with Flange) 7. 2" (182. 8 mm) Depth without socket - no lens 5. 5" (140. 0 mm) Depth with Socket - no lens 6. 6" (167. 2 mm) Depth without socket with lens 6. 1" (153. 8 mm) Depth with Socket with lens 7. 1" (181. 0 mm) OD of 6" Flange 7. 6" (192. 0 mm) OD of 5" Flange 6. 7" (171. 2 mm) Weight 2. 51 lbs (1. 14 kg) 19 Tech Support: 1-800-KLIPSCH Possible causes of interference with your LightSpeaker® 5 A) Metal studs, in fact any metal wall material, can cause the signal to be diminished or lost. This may also be a problem if your wall paper happens to be a foil type or have metal fibers in it. B) Microwave ovens, when operating, may degrade or interrupt the signal from your transmitter. Usually this will only be a problem for those speakers in close proximity to the microwave. C) Certain portable phones operating in the 2. 4 Ghz range, wireless computer routers, and other consumer electronics and toys using 2. 4 Ghz may cause interference when operated too close to either the transmitter or the speakers. 20 Tech Support: 1-800-KLIPSCH Warranty - Home and Commercial Audio (U. S. ) The Warranty below is valid only for sales to consumers in the United States. [. . . ] EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE. Some states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights, which vary from state to state. OUTSIDE THE UNITED STATES AND CANADA The warranty on this product if it is sold to a consumer outside of the United States or Canada shall comply with applicable law and shall be the sole responsibility of the distributor that supplied this product. [. . . ]