User manual KLIPSCH IC-SW-8T2

[. . . ] I C - S W- 8 T 2 IN-CEILING SUBWOOFER OWNER'S MANUAL AND WARRANT Y IC-SW-8T2 Thank you for purc hasing your Klipsc h IC-SW-8T2 in-ceiling subwoofer. To install the tilebridge, fold the rail side of the ring back upon itself using the spring tensioner on the reinforcement ring to allow insertion into the cutout hole. Once it is inserted into the cutout hole, release the reinforcement ring such that it unfolds back to its normal position. [. . . ] Access to this compartment is gained by removing the terminal cover located on the back of the speaker. The terminal cover will accept the appropriate conduit/wire adapter (provided). Feed wires through conduit/wire adapter and connect to the input terminal according to the desired operation mode. Replace the terminal cover and tighten the conduit/wire adapter to secure the wire. Caution: Be sure to comply with any and all building codes in your area. Caution: When connecting 70V or 100V distributed line systems, take care to ensure proper terminal connection. Connection to the low impedance terminal could result in speaker damage, amplifier damage, or both. 2. To install your IC-SW-8T2 cut out a hole in the ceiling using either the cardboard cutout template provided with your speakers or consult the measurements below. With a #2 Phillips screwdriver, tighten the four dog clamps until they are seated securely against the ceiling surface. For installations using 70v/100v input connection, set the switch on the front panel to "70V/100V". For low impedance, stereo applications, the switch should be set to 8 ohms stereo. For low impedance, mono applications, the switch should be set to 4 ohm mono. In all cases, please make sure the speaker wires are connected to the appropriate terminal on the back. 60W 70 30W 10 0V IC-SW-8T2 tap selectable 7. Using the flat of your hand, insert grille into speaker frame making sure it is securely seated and flush. Seismic Tab A seismic tab, located on the back of the speaker, is used as a secondary security point. To utilize the seismic tab, run a support wire from a secure point in the ceiling and attach it to the tab. Klipsch recommends the use of this tab in all installations as a secondary means of support. V 60W 120W IN - CEILING SUBWOOFER IC-SW-8T2 S P E C I F I C AT I O N S IC-SW-8T2 FREQUENCY RESPONSE C O N T. O U T P U T @ 1 M SENSITIVIT Y 2. 83 V/1M C OV E R AG E DI Q N O M I N A L I M P E DA N C E DIAMETER C U TO U T D I A M E T E R OV E R A L L D E P T H MOUNTING DEPTH WEIGHT I N P U T C O N N E C TO R S T R A N S F O R M E R TA P S FINISHES TRANSDUCERS E N C LO S U R E T U N I N G 5 0 - 13 0 H z + / - 4 d B 150 watts (27 V) 111 dB 92 dB N/A N/A N/A 6 ohms, min 4. 9 ohms, switch set to mono or stereo position 14. 125" 14. 25" 13. 625" 13. 313" 23 lbs. Te r m i n a l S t r i p 7 0 V: 6 0 W, 3 0 W 10 0 V: 12 0 W, 6 0 W White 8 " Wo o f e r A N D 8 ' D r o n e Bandpass via an 8" Drone ©2003 Klipsch Audio Technologies All Rights Reserved Specifications Subject to Engineering Changes Klipsc h Limited Warranty KLIPSCH, AUDIO TECHNOLOGIES ("KLIPSCH") warrants this product to be free from defects in materials and workmanship (subject to the terms set forth below) for a period of five (5) years from the date of purchase. During the Warranty period, KLIPSCH will repair or replace (at KLIPSCH's option) this product or any defective parts (excluding electronics and amplifiers). [. . . ] KLIPSCH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE. Some states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights, which vary from state to state. 3502 Woodview Trace, Suite 200 Indianapolis, Indiana 46268 USA 1. [. . . ]