User manual KLIPSCH COMM SAT

[. . . ] If the provided plug does not fit into your outlet, consult electrician for replacement of the obsolete outlet. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. [. . . ] Feed wires through conduit/wire adapter and connect to the terminal strip according to the desired operation mode. Replace enclosure cover after completing all connections properly and tighten the conduit/wire adapters to secure the wires. Caution: When connecting 70V or 100V distributed line systems, take care to ensure proper terminal connections. Incorrect connections could result in speaker damage, amplifier damage, or both. WARNING: Voltages in this equipment are hazardous to life. CAUTION: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this device. ABOUT YOUR KLIPSCH PURCHASE Thank you for purchasing the Klipsch Comm Sat speaker system. The Comm Sat speaker system is designed for music reinforcement applications. The speakers are engineered for easy, unobtrusive installations and can be used to create a variety of different configurations. Figure 1 2. First, attach the Speaker to the Mount post (included with the Mount). Now pull the wire pigtail attached to the Comm Sat through the hole in the Mount tube and plate and make your connections in the box behind the plate. With the adjustment point on the Mount loose, adjust Speaker direction as desired. Tighten adjustment point on the Mount with the supplied tool after the Speaker is aimed as desired. AND CANADA ONLY The Warranty below is valid only for sales to consumers in the United States or Canada. KLIPSCH AUDIO TECHNOLOGIES warrants this product to be free from defects in materials and workmanship (subject to the terms set forth below) for a period of five (5) years from the date of purchase. During the Warranty period, KLIPSCH will repair or replace (at KLIPSCH's option) this product or any defective parts (excluding electronics and amplifiers). For products that have electronics or amplifiers, the Warranty on those parts is for a period of two (2) years from the date of purchase. To obtain Warranty service, please contact the KLIPSCH authorized dealer from which you purchased this product. If your dealer is not equipped to perform the repair of your KLIPSCH product, it can be returned, freight paid, to KLIPSCH for repair. You will need to ship this product in either its original packaging or packaging affording an equal degree of protection. Proof of purchase in the form of a bill of sale or receipted invoice, which is evidence that this product is within the Warranty period, must be presented or included to obtain Warranty service. [. . . ] Install the Subwoofer of your choice, (You may use either the IC-8T-SW flushmount subwoofer or the CA-800-TSW surface-mount subwoofer with this system) following the installation instructions that are supplied with the subwoofer. C O M M S AT N E T W O R K S P E C I F I C AT I O N S COMM SAT NETWORK BANDWIDTH 1 TRANSFORMER TAPS CROSSOVER INPUT CONNECTORS ENCLOSURE MATERIAL HEIGHT WIDTH DEPTH WEIGHT SHIPPING WEIGHT FINISH n/a 70V: 30W, 100V: 60W 100Hz 12dB/Octave highpass Barrier strip Steel 4. 375" (11. 1cm) 6. 125" (15. 6cm) 6. 125" (15. 6cm) 5 lbs. (2. 7kg) Gray ©2004 Klipsch Audio Technologies All Rights Reserved Specifications Subject to Engineering Changes C O M M S AT S P E A K E R S P E C I F I C AT I O N S COMM SAT SPEAKER BANDWIDTH 1 POWER HANDLING2 MAX CONT. SPL 3 SENSITIVITY 4 NOMINAL IMPEDANCE HIGH FREQUENCY CROSSOVER DRIVE COMPONENTS 120Hz-20kHZ ± 4dB (-10dB @ 42Hz) 70W (15. 5V @ 3. 2 ohm input) 107dB 90dB @ 2. 83 volts/1 meter 8 ohms (3. 2 ohm minimum @ 5. 5Hz) 4900Hz Two-way system using one . 75" (1. 9cm) magnetically shielded, cloth dome compression driver tweeter with a 90° x 40° Tractrix® Horn and one 3. 5" (8. 9cm) magnetically shielded, poly cone woofer HIGH FREQUENCY HORN SYSTEM CROSSOVER INPUT CONNECTORS ENCLOSURE TYPE ENCLOSURE MATERIAL HEIGHT WIDTH DEPTH WEIGHT SHIPPING WEIGHT FINISH MOUNTING 90° x 40° Tractrix® Horn Comm Sat Network Required Pig tail wire attached Bass reflex via rear-mounted port Stone mineral compound 7. 5" (19. 1cm) 4. 25" (10. 8cm) 6. 4" (16. 2cm) 4 lbs. (3. 6kg) / pair Black or White Comm Sat Mount (optional) 1 3M, Half-space anechoic 2 AES Standard, continuous pink noise 50Hz-10kHz, 6dB peaks 3 Calculated at 1M half-space at power handling power input 4 SPL at 1M, half-space anechoic with 2. 83V input ©2004 Klipsch Audio Technologies All Rights Reserved Specifications Subject to Engineering Changes S U B W O O F E R S P E C I F I C AT I O N S CA-800-TSW FREQUENCY RESPONSE 1 POWER HANDLING 2 MAX CONTINUOUS OUTPUT 3 SENSITIVITY (2. 83V/1M) 4 NOMINAL IMPEDANCE CROSSOVER TRANSDUCERS ENCLOSURE TUNING ENCLOSURE MATERIAL INPUT CONNECTORS TRANSFORMER TAPS HEIGHT WIDTH DEPTH WEIGHT 1 3M, half space anechoic 2 AES standard, continuous pink noise 50Hz-10Hz, 6dB peaks 3 Calculated at IM at power handling power input 4 SPL at 1M, half-space anechoic with 2. 83V input 51-135kHz ± 4dB -10dB 42Hz 150W (25V) 111dB 92dB 6 ohms (4 ohm min @92Hz) 12dB/Octave low-pass, 150Hz One 8" woofer with IMG cone Vented System via front firing ports All-weather ABS plastic, paintable 4 point terminal strip 70V: 60W, 30W, 15W, 7. 5W, 3. 75W 100V: 60W, 30W, 15W, 7. 5W 11. 125" (28. 26cm) 16. 375" (41. 53cm) 12. 313" (31. 28cm) 20 lbs. [. . . ]