User manual KLIPSCH AW-800-SW

[. . . ] This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. WARNING: To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture. KLIPSCH REFERENCE ALL-WEATHER LOUDSPEAKERS (AW-400, AW-500, AW-525, AW-650, AW-500-SM models) The Klipsch Reference All-Weather loudspeakers are two-way designs using a high performance bass driver for the low frequencies. A Tractrix Horn with a 90° x 90° coverage pattern attached to a 1" diameter compression driver for clean and efficient reproduction of the high and midrange frequencies. (AW-800-SW) The AW-800-SW is an innovative approach that delivers low frequency sound in outdoor applications. [. . . ] Be sure to leave enough clearance between the end of the bracket and any adjacent wall or ceiling for installation of the knobs. If a wall stud is not available, use the appropriate type of drywall or masonry anchor to support the weight of the speaker, allowing for a generous safety margin. Please consult your dealer, custom installer or building contractor in these situations. ABOUT YOUR KLIPSCH PURCHASE Thank you for your purchase of Klipsch outdoor loudspeakers. After reading this manual and connecting your system, you will hear the result of over 55 years of stringent engineering and class-leading research and development. Like all Klipsch products, your outdoor loudspeakers feature Klipsch Tractrix® Horn-loaded Technology--the guiding design for the first Klipschorn® developed in 1946 and for every product that has followed. Horn-loading allows your speakers to deliver high sensitivity, low distortion, flat frequency response and wide dispersion, which translates to unequaled power, detail and dynamics, the hallmarks of "The Klipsch Sound. " Please be sure to fill out the warranty card at the back of this manual or online at www. klipsch. com so we are better able to serve you. Again, thank you for choosing Klipsch and we hope that your speakers bring life to your music for many years. You may also use an optional wall or ceiling mount that will fit the provided 3/8" ­ 16 inserts. Please see your authorized Klipsch dealer to see which model is right for you. CONNECTIONS (AW-500-SM model) The AW-500-SM can operate in two modes. When using one speaker, flip the switch to the "Stereo" position and connect the "Front" or "Main" left and right channels of your system's power amplifier to both inputs (See Figure 2A). When using more than one AW-500-SM, flip the switch to the "Mono" position and connect either output of your system's power amplifier to either input cup (See Figure 2B). Note: Proper connection of your speakers to your amplifier or receiver is vital to obtaining good sound quality. Use a lower gauge (heavier) wire for longer runs to reduce the amount of amplifier power lost due to the wire's resistance. A Figure 2 BUT FIRST: TYPES OF CONNECTORS Bare wire. Pull the two conductors apart for about an inch and strip approximately 1/4-inch of insulation from the end of each. (A wire stripper will simplify this, but you can use an ordinary pocket knife to cut around and through the insulation down to the wire. ) Twist the strands of wire on each individual conductor tightly together. Loosen the nuts on a pair of binding posts until the holes through the metal posts are exposed, then insert the bare wire through the holes. Make sure that no strands of wire are touching from one binding post to the other or to any strands from the other conductor. Failure to observe this precaution at either end of the connection can result in amplifier malfunction or damage. Loosen the nuts on a pair of binding posts until the holes through the metal posts are exposed, then insert the pins through the holes. Make sure that there is no metal-to-metal contact between the two pins or binding posts. Failure to observe this precaution at either end of the connection can result in amplifier malfunction or damage. Some speaker cables are terminated with U-shaped connectors called spade lugs. Loosen the nuts on a pair of binding posts and slip the spade lugs around the metal posts. Screw the nuts down finger-tight on the lugs and inspect to ensure they have remained firmly in place. [. . . ] KLIPSCH DOES NOT ACCEPT LIABILITY FOR SPECIAL, INDIRECT, CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING WITHOUT LIMITATION, ANY LIABILITY FOR THIRD PARTY CLAIMS AGAINST YOU FOR DAMAGES OR FOR PRODUCTS NOT BEING AVAILABLE FOR USE. If this product proves defective in either material or workmanship, Klipsch, at its option, will (a) repair the product, or (b) replace the product, at no charge for parts or labor. If the product model is no longer available and cannot be repaired effectively or replaced with an identical model, Klipsch at its sole option may replace the unit with a current model of equal or greater value. In some cases, modification to the mounting surface may be required where a new model is substituted. [. . . ]