User manual KINOTON FP 30 D MANUAL 1

[. . . ] The FP 30 D projector is only to be employed for its intended purpose and is only used when functioning absolutely perfectly . Serious danger may result from improper use of the system causing injury to the user or a third person, or damage may be done to the system or other items in the vicinity. Faults that could adversely affect safety must be rectified immediately. The projector cannot be used before faults are rectified. Operating Manual 1-1 Intended Purpose The FP 30 D projector is only suitable to reproduce 35 mm films and sound. [. . . ] DANGER Open lamphouse after a waiting period of 10 minutes. , vertical The current of lamp and rectifier must be switched off all-polo. Work at open lamphouse to be carried out has to be done with protective suit, cloves and face shield. You can seriously hurt yourself when xenon bulb explodes and broken glass is flying around. 2. Carry out the following adjustments through the associated holes in lamphouse housing. With the aid of the hexagon screw , the xenon lamp is adjusted as much along the optical axis until only a reduced round illuminated spot can be seen on screen. By turning adjusting screws right left (horizontally) and up down (vertically) you have to bring this light spot precisely into the middle of the screen. Operating Manual 2-21 7. By turning the hexagon screw , mount the spot until the screen is illuminated evenly. NOTE Whenever in extreme special cases the described way to adjust is not possible, you can change the mirror position with the aid of the adjusting screws of mirror holder. The light arc adjustment is to be carried out by experts only, see operating manual Universal Lamphouse . 2. 4. 1. 5 Inserting Heat Filter A heat filter is necessary from a lamp capacity of 2500 W onwards. ATTENTION The heat filter is a reflection filter, therefore you have to watch out for the reflection side of filter to be directed to xenon lamp. You can see the edge of reflection coating when you look at the small side of filter holding it against the light. Touch the filter on one edge with your fingers - On the adhesive side you will see a fingerprint. Lamphouse up to 2000 W 2000 to 7000 W Figure 2-13 Heat filter clamping bar heat filter holders 1. Lamphouse up to 2000 W: Insert filter under clamping bar fasten screws of clamping bar. Lamphouse from 2000 W onwards: Put heat filter on the lower holders and press the filter against the spring (arrow) until it arrests at the end of the spring (clamping). 2-22 : Kinomedia. net ® , 2008 . FP 30 D 2. 4. 2 Filling in Projector Oil NOTE Use oil type 3672 only. plug on oil gauge glass breather tube intermittent movement (maltese cross) oil level ring (red and green) hose Figure 2-14 Intermittent movement with oil gauge glass 1. Put hose out of clamp (not visible in figure 2-14) and remove red hose cap. Fill oil by means of funnel or squeeze container into the hose up to the level in the middle between the red and green oil level ring in the oil gauge glass. Turn intermittent movement manually and rotate framing knob several times so air bubbles can escape. This was only for shipping the projector. Operating Manual 2-23 2. 4. 3 Projector Terminal Strips The terminal strip with terminals 1 to 25 is mounted on the bottom of the projector. Squeeze wires (see plan of terminal connections). Figure 2-15 Terminal strip of FP 30 D projector The terminal strip with terminals 1 to 58 is mounted on the bottom of the projector. Squeeze wires (see plan of terminal connections). Figure 2-16 Terminal strip FP 30 D-F The terminal strip (arrow) with terminals 1 to 41 is mounted on the bottom of the projector. Squeeze wires (see plan of terminal connections). Figure 2-17 Terminal strip FP 30 D-A NOTE You will find the plans of terminal connections for FP 30 D / D-F / D-A in chapter 8. 3. 2, 8. 3. 3 and 8. 3. 4. ATTENTION Allow connecting the wires to be carried out by competent electricians only. 2-24 : Kinomedia. net ® , 2008 . FP 30 D 2. 4. 4 Operating Panel Connections (only FP 30 D) 30 pole male receptacle for control panel (auditorium light, curtain etc. ) 1 2 30 pole female receptacle for control panel (projector functions) operating panel 3 Figure 2-18 Connections (only FP 30 D) NOTE You will find the plans of connections for 30 pole male and female receptacle in chapter 8. 3. 5. 2. 4. 5 Non-Rewind System Install non-rewind system. [. . . ] The height of the amplitude appropriates to loudness, frequency and to pitch. The digital sound information (DTS) is encoded between film picture and analog sound track. The SDDS information is encoded on the sides of the film (in figure beside you see only one side). Figure 3-25 Sound tracks on film The reverse-scan sound device (arrow) contains an analog sound element and a digital sound one (DOLBY SR?D and Unlike the standard sound device the readers of reverse-scan sound device (analog and digital) take their information from the coated side of the film. [. . . ]