User manual KETTLER PEDAL RACER

[. . . ] This KETTLER product has been designed in accordance with the latest standards of safety and subject to constant quality monitoring. The data gained from this quality process is then incorporated in the development of our products. For this reason, we reserve the right to make changes in design and technology in order to offer our customers products of the highest standard of quality at all times. In spite of this, if you have any comments please contact KETTLER International, Inc. For your safety This pedal car should be used for its intended purpose only, i. e. [. . . ] Never use near steps, slopes, driveways, hills, roadways, alleys or swimming pool areas. Before use always check that all screws and plug-in connections and respective safety devices t correctly. Do not leave children who are not old enough to use the wheeled toy unattended on a product. Instruct your child how to use the vehicle correctly and draw attention to possible sources of danger. The seat of this product can be adjusted to your child's size. 2 USA Assembly Instructions Please bear in mind that there is always a danger of children injuring themselves while using swings, climbing frames, toy vehicles or similar equipment. When riding the toy, the child should always wear covered footwear (no open toe shoes or barefoot riding). When children are at play, situations may arise which cannot be predicted by the manufacturer and for which he cannot be held responsible. For models with air tires, check air pressure periodically (see tire for recommended psi) Due to the nature of materials used in air tires on Racer by Kettler® toys, it is not recommended that the product to be left in any one place for too long where solvents or other chemicals, i. This may result in a chemical reaction, which could cause the tires to mark the surface such as a vinyl If in doubt put something underneath the wheels to cover Lubricate the bearing sleeves of the wheels with a few drops of oil every two to three months. Assembly of the Pedal Car Please ensure that the vehicle will only be used for playing when assembly has been carried out correctly, and checked, by an adult. Assemble the vehicle in the exact sequence shown by the letters in the diagrams. Please note that there is always a danger of injury when working with tools or doing manual work. Ensure that your working area is free of possible sources of danger, for example don't leave any tools lying around. Always dispose of packaging material in such a way that it may not cause any danger. Bolt all the parts together loosely at and check that they have been assembled correctly. Tighten the locknuts by hand until resistance is felt, then use the wrench to tighten nuts completely against resistance (locking device). Attention: once locknuts have been unscrewed they no longer function correctly (the locking device is destroyed), and must be replaced. Please keep original packaging of this article, so that it may be used for transport at a later date, if necessary. For technical reasons, we reserve the right to carry out preliminary assembly work (e. g. When ordering spare parts, always state the full model number, spare part number, the quantity required and the serial number of the product. Important: spare part prices do not include fastening material; if fastening material (bolts, nuts, washers etc. ) is required it should be clearly stated on the order by adding the words , , with fastening material". 3 USA Racer by Kettler® Limited Warranty THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, MADE BY EITHER THE DISTRIBUTOR OR THE MANUFACTURER ON RACER BY KETTLER® PRODUCTS, EXCEPT THE MANUFACTURER'S LIMITED WARRANTY AGAINST DEFECTS IN MATERIAL SET OUT BELOW: This Racer by Kettler® Limited Warranty applies to products sold through the Racer by Kettler® Authorized Dealer Network to the original retail purchaser and authenticated by proof of purchase from a retailer located in the United States. [. . . ] 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 description main frame tie rod tie rod pin running wheel spacer sleeve drive wheel wheel cover for drive wheel frame guard wheel screen seat steering wheel rod steering wheel steering wheel bolt set steering column frame steering wheel cap steering column casing grill upper chain guard cover lower chain guard cover pedal crank bearing clamp, pedal crank bearing clutch lever clutch grip plug axle chain axle bearing clamp, axle bearing brake lever brake grip clamp for brake lever pedal crank adjustment mechanism tire rod cover, right tire rod cover, left hubcap front frame rear frame hardware bag qty. 1 1 1 3 2 1 1 2 4 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 2 1 1 2 2 1 1 2 1 2 1 1 4 1 1 1 part no. 8881-540#01 8881-540#02 8881-540#03 8881-540#04 8881-540#05 8881-540#06 8881-540#07 8881-540#08 8881-540#09 8881-540#10 8881-540#11 8881-540#12 8881-540#13 8881-540#14 8881-540#15 8881-540#16 8881-540#17 8881-540#18 8881-540#19 8881-540#20 8881-540#21 8881-540#22 8881-540#23 8881-540#24 8881-540#25 8881-540#26 8881-540#27 8881-540#28 8881-540#29 8881-540#30 8881-540#31 8881-540#32 8881-540#33 8881-540#34 8881-540#35 8881-540#36 8881-540#37 8881-540#38 8881-540#39 8881-540#40 © 2008 RACER by Kettler. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form, or by any means, such as electronic, mechanical, photocopying or otherwise, without prior written permission from KETTLER® 18 USA Addendum for RACER Pedal Car Model #8881-740 pos. [. . . ]