User manual KETTLER FRONT LOADER 813001

[. . . ] Insert one of the front wheel push nuts (100. 200. 100. 00) into one of the plastic tools provided. Tap the push nut (100. 200. 100. 00) onto the end of the front wheel axle (001. 000. 010. 00) using a mallet/hammer and the plastic tool. Slide one of the front wheel covers (286. 000. 022. 13) onto the front wheel axle (001. 000. 010. 00). Next, slide one of the front wheels (555. 000. 004. 80) onto the front wheel axle. [. . . ] Connect the left side loader arm (932. 061. 002. 13) to the main frame (932. 000. 007. 13). Attach the right side loader arm (932. 061. 001. 13) to the left side loader arm (932. 061. 002. 13). Insert the m8x70 bolt through the left side loader arm (932. 061. 002. 13) at the area where it connects to the main frame (932. 000. 007. 13). Make sure to hold the nut in place in the right side arm while tightening the bolt. Connect the right arm handle (932. 063. 001. 13) to the right side loader arm (932. 061. 001. 13) and insert the m6x70 bolt through the arm handle. Connect the left arm handle (932. 063. 002. 13) to the left side loader arm (932. 061. 002. 13) and insert the m6 cap nut into the arm handle. Connect the center lever arm (932. 000. 065. 75) to the right arm handle (932. 063. 001. 13). Insert the m6x20 bolt with the metal washer into the center lever arm (932. 000. 065. 75). Line up the hole at the end of the center lever arm (932. 000. 065. 75) with the hole at the end of the center loader arm (932. 000. 067. 13). Insert the m6 cap nut into the center loader arm (932. 000. 067. 13) Tighten the m6x16 bolt using a screw driver. Attach the bucket loader arms (932. 000. 068. 75) to the backhoe bucket (932. 000. 059. 80). Insert the end of the bucket loader arms (932. 000. 068. 75) in between the right and left side loader arms (932. 061. 002. 13 and 932. 061. 001. 13). Be sure to line the holes up in the bucket loader arms with holes in the right and left side loader arms. Insert the m6x55 bolt into the left side loader arm (932. 061. 002. 13) and through the bucket loader arms (932. 000. 068. 75). Insert the m6 cap nut into the right side loader arm (932. 061. 001. 13). Line up the holes on the backhoe bucket (932. 000. 059. 80) with holes on the center loader arm (932. 000. 067. 13) and insert the m6x35 bolt through the left side. Using a wrench hold the nut still and tighten the m6x35 bolt with a screw driver. Step 7b. Step 13. Slide the backhoe seat (261. 000. 007. 80) onto the main frame (932. 000. 007. 13). Secure the backhoe seat (261. 000. 007. 80) in place by screwing the m4x17 screw through the seat and into the main frame (932. 000. 007. 13) using a screw driver. Insert the pin (932. 000. 006. 22) into the bottom of the backhoe where it connects to the tractor hitch to secure the backhoe to the tractor. [. . . ] Tap the end of the metal shaft with tabbed ends (499. 000. 010. 00) into one of the plastic knobs (499. 060. 021. 22). Insert the metal shaft with the tabbed ends (499. 000. 010. 00) into the opening in the side of the front of the tractor. Gently tap the other plastic knob (499. 060. 021. 22) onto the other side of the metal shaft with tabbed ends (499. 000. 010. 00). Insert the plastic bushings (499. 060. 018. 80) into the holes in front of the tractor. [. . . ]