User manual KENWOOD TM-331A

[. . . ] TM-D700A: 144/440 MHz FM Dual Bander (U. S. A. / Canada) TM-331A: 144/430 MHz FM Dual Bander (Europe) TM-D700A: 144/430 MHz FM Dual Bander (General market) · Is capable of receiving packet data on one band while receiving audio on the other band. · Enhanced Programmable Memory (PM) channels store virtually entire current operating environments for your quick recall. · Contains a total of 200 memory channels to program frequencies and other various data. Allows each memory channel to be named using up to 8 alphanumeric and special ASCII characters. [. . . ] · When programming as an odd-split channel, press [F], [C. IN] (1 s) instead; "±" appears. 7 s Recalling the Call Channel 1 Select the desired band. 2 Press [CALL] to recall the Call channel. · "CALL" appears. To also store a transmit frequency, proceed to the next step. 6 Press [C. IN]. · The transmit frequency is stored in the Call channel, and the previous mode is restored. Note: x Transmit Offset status and Reverse status are not stored in an odd-split Call channel. x To store data other than frequencies, select the data in step 3 not step 5. · To restore the previous mode, press [CALL] again. 39 MEMORY-TO-VFO TRANSFER You may sometimes want to search for other stations or a clear frequency, near the frequency stored in a memory channel or the Call channel. In this case first transfer the contents of a memory channel or the Call channel to the VFO. s 7 · The entire contents of the memory channel or the Call channel are copied to the VFO. Note: x A transmit frequency from an odd-split memory channel or odd-split Call channel is not transferred to the VFO. s x Lockout status and memory names are not copied from a memory channel to the VFO. x If you recall the Call channel in step 1, simply turning the Tuning Control or pressing Mic [UP]/ [DWN] also transfers the contents to the VFO. The frequency, however, is changed by one step. CHANNEL DISPLAY When in this mode, the transceiver displays only memory channel numbers (and memory names if stored) instead of frequencies. 2 Press [c]/ [d] to select "RADIO (1­)", then press cd [OK]. 3 Press [c]/ [d] to select "MEMORY (1­4­)", then cd press [OK]. Situation 3 Situation 3 You cannot figure out how you can make the transceiver exit the current mode. Solution Solution Simply recall PM channel 1 that contains an exact copy of the transceiver default environment. You will not lose the contents of any memory channels. 43 STORING IN PM CHANNELS 1 Confirm that the following conditions have been satisfied: · The transceiver is in the receive mode. · Microphone Control is OFF. RECALLING A PM CHANNEL 1 Press [PM]. · The PM channel numbers 1 to 5 appear at the bottom of the display. 2 Configure the transceiver as you like. · For the items that can be stored, see page 42. 3 Press [F], [P. IN]. 8 · The PM channel numbers 1 to 5 appear and blink at the bottom of the display. 2 Press [1] to [5] corresponding to the desired PM channel. · The contents of the selected channel are recalled. · The current PM channel number appears at the upper right corner. "s" before "PM" indicates that Auto PM Store mode {page 45} has been selected. · To exit PM Recall mode, press [PM], then press [OFF]. Note: You cannot recall a PM channel while transmitting. 4 Press [1] to [5] corresponding to the desired PM channel. · The settings listed in page 42 are stored in the PM channel. 44 AUTO PM CHANNEL STORE After you recalled a PM channel, this function automatically overwrites the current PM channel with the present operating environment when: · You recall another PM channel. · You switch OFF the transceiver. PM CHANNEL RESET If you want to reprogram the PM channels from the beginning, reset all the PM channels to the factory defaults. 1 Press [PM]+ POWER ON. · A confirmation message appears. The factory default of this function is ON. 2 Press [c ]/ [d] to select "RADIO (1­)", then press cd [OK]. 3 Press [c]/ [d] to select "MEMORY (1­4­)", then cd press [OK]. [. . . ] Nothing 2 One or more of the power cable fuses 2 Look for the cause of the blown fuse(s). inspecting and correcting any problems, install a new fuse(s) with the same ratings. 3 The modular plug cable was not 3 Correctly connect the modular plug cable correctly connected. The supply voltage requirement is though you selected a high 13. 8 V DC ±15% (11. 7 V to 15. 8 V DC). [. . . ]