User manual KENWOOD RC2000

[. . . ] INSTRUCTION MANUAL MOBILE CONTROLLER RC-2000 MOBILE CONTROLLER RC-2000 KENWOOD CORPORATION © B62-1292-10 (M) 09 08 07 06 05 04 03 02 01 SUPPLIED ACCESSORIES Accessory RC-2000 Mobile Controller DC power cable (7 m/ 23. 1 ft) Microphone extension cable (5 m/ 16. 5 ft) Speaker extension cable (5 m/ 16. 5 ft) RC-2000 cable with modular plugs (5 m/ 16. 5 ft) RC-2000 bracket1 Part Number ­ E30-3406-XX E30-3407-XX E30-3408-XX E30-3409-XX Quantity 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 CONVENTIONS FOLLOWED IN THIS MANUAL The writing conventions described below have been followed to simplify instructions and avoid unnecessary repetition. With transceiver power OFF, press and hold KEY, then turn ON the transceiver power by pressing [ ]. Refer to page XX of this manual. J29-0663-XX J29-0664-XX Screw set (for RC-2000 bracket) N99-2014-XX TS-2000(X)/ TS-B2000 A13-0635-XX Mounting bracket Spacers (for A13-0635-XX) J30-0521-XX Screw set (for A13-0635-XX) N99-2024-XX Speaker with cable and plug T19-0116-XX Screw set (for T19-0116-XX and N99-2017-XX A13-0635-XX) Line filters: For microphone (large) L79-1419-XX For panel and speaker (small) L79-1417-XX Fuse (25 A/ 32 V) F05-2531-XX Warranty card: For the U. S. A. and Canada B46-0469-XX For European Countries B46-0310-XX Instruction manual B62-1292-XX 2 parts are used. Refer to page XX in the {TS-2000 page XX} TS-2000(X)/ TS-B2000 instruction manual. 1 CONTENTS CHAPTER 1 ABOUT THIS MANUAL BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Adjust the monitor level using the [c]/ [d] keys or by turning the MULTI/ CH control, then press either [EXIT] or the MULTI/ CH control to store the setting. RF Refer to RF in the CW section {page 24}. GROUP C­3 N. R. Press to activate Noise Reduction 1, Noise Reduction 2, or to turn the function OFF. When the noise reduction function is ON, "N. R. 1" or "N. R. 2" appears above the key. When it is ON, press and hold the key to change the noise reduction level. Adjust the noise reduction level using the [c]/ [d] keys or by turning the MULTI/ CH control, then press either [EXIT] or the MULTI/ CH control to store the setting. PWR Press to adjust the output power {TS-2000 page 20}. Adjust the output power using the [c]/ [d] keys or by turning the MULTI/ CH control, then press either [EXIT] or the MULTI/ CH control to store the setting. GROUP C­2 VOX Press to switch the Voice-Operated Transmission function ON or OFF {TS-2000 page 39}. A. N. Press to switch the Auto Notch function ON or OFF. Adjust the Auto Notch tracking time constant using the [c]/ [d] keys or by turning the MULTI/ CH control, then press either [EXIT] or the MULTI/ CH control to store the setting. V GAIN Press to adjust the VOX gain {TS-2000 page 39}. While pressing Mic [PTT], adjust the VOX gain using the [c]/ [d] keys or by turning the MULTI/ CH control, then press either [EXIT] or the MULTI/ CH control to store the setting. B. C. Press to switch the automatic Beat Cancel function ON or OFF. "B. C. " and "DSP" appear when it is ON. V DLY Press to adjust the VOX delay time. Select your desired delay time using the [c]/ [d] keys or by turning the MULTI/ CH control, then press either [EXIT] or the MULTI/ CH control to change the setting. in the CW section {page 24}. FILTER Refer to FILTER in the CW section {page 24}. CW MODE Action Press and hold the key: [C­1] [CW TUN] CW Tune function ON/ OFF CW Tune function ON/ OFF [CAR] [REV] -- -- [PWR] Output power adjustment -- Press the key: Move to C­2 Move to group A­1 Reverse the sideAdjust a carrier level tone pitch frequency -- -- Action Press and hold the key: [C­2] [VOX] Break-in ON/ OFF -- -- -- [BK DLY] Adjust the Break-in delay time -- [KEY] Adjust the electric keyer speed -- [RF] RF gain adjustment -- Press the key: Move to C­3 Move to group A­1 Action Press and hold the key: [C­3] [N. R. ] Noise Reduction 1 or 2 ON/ OFF Adjust the Noise Reductoin parameter -- -- -- -- [M. B. C. ] [FILTER] Press the key: Move to C­1 Move to group A­1 Manual Beat Cancel Configure DSP filter ON/ OFF setting Adjust Manual Beat -- Cancel frequency GROUP C­1 CW TUNE Press to activate the CW Auto Tune function. Press [CW TUN] again or [CLR] to exit the function. REV Press to reverse the side-tone pitch. "CWR" appears when it is ON. PWR Refer to the USB/ LSB section {page 22}. CAR Press to enter the carrier level adjustment mode. Adjust the carrier level within the ALC zone using the [c]/ [d] keys or by turning the MULTI/ CH control, then press either [EXIT] or the MULTI/ CH control to change the setting. 23 GROUP C­2 VOX Press to switch the CW break-in function ON or OFF. GROUP C­3 N. R. Refer to N. R. in the USB/ LSB section {page 22}. BK DLY Press to adjust the CW break-in delay time {TS-2000 page 42}. Select your desired break-in delay time using the [c]/ [d] keys or by turning the MULTI/ CH control, then press either [EXIT] or the MULTI/ CH control to change the setting. The values range from FBK (full break-in) to 100 which is the slowest delay time. M. B. C. Press to switch the Manual Beat Cancel function ON or OFF. Press and hold the key to enter the manual beat cancel frequency adjustment mode. Adjust the beat cancel frequency using the [c]/ [d] keys or by turning the MULTI/ CH control, then press either [EXIT] or the MULTI/ CH control to store the setting. KEY Press to adjust the keying speed of the electric keyer. Select your desired keying speed using the [c]/ [d] keys or by turning the MULTI/ CH control, then press either [EXIT] or MULTI/ CH control to change the setting. The adjustable keying speed is between 10 (WPM) and 60 (WPM). FILTER USB/ LSB/ FM/ AM mode: Press to adjust the low cut-off or high cut-off frequency of the DSP. Press [HI] or [LOW] to select the high or low cut-off, then press [c]/ [d] or turn the MULTI/ CH cd control to select the desired cut-off frequency. CW/ FSK mode: Press to adjust the DSP filter width or shift frequency. [. . . ] Instruction Press [R1]+ [ ] (POWER) Press [L2]+ [ ] (POWER) Press [L3]+ [ ] (POWER) Function Resets the contents of PM (Programmable Memory) to the factory default values {page 42}. 2 To exit the demonstration mode, first turn the transceiver OFF, then press [F1]+[ ] (POWER) on the RC-2000 to turn the transceiver ON. Note: You cannot exit the demonstration mode by simply switching the transceiver OFF or performing a full reset {TS-2000 page 92}. CONFIGURING THE AUTO MODE FREQUENCY TABLE To configure the Auto Mode frequency table: 1 Press [F6]+[ ] (POWER) on the RC-2000 to switch the transceiver ON. Tuning control: Adjust the frequency MULTI/ CH control: Change the channel number [MODE]/ [REV]: Change the operating mode [UP]/ [DWN]/ [1MHz]: Change the operating band 3 Press [OK] to store the settings. When a confirmation message appears, press [OK] to proceed. Otherwise, press any other key to cancel the operation. CONCERNING THE TM-D700A/E PANEL The RC-2000 control panel can be used in place of the TM-D700A/E panel. [. . . ]