User manual KENWOOD LZ-6500W

[. . . ] · When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction. · To prevent short circuits when replacing a fuse, first disconnect the wiring harness. To enjoy video pictures, find a safe place to park and engage the parking brake. [. . . ] Display the setup screen for 5 seconds as follows: · Screen mode · Video source · Audio source · Volume [FULL] [ZOOM] 1 Mode Setting switch Selects the target device to control. MON: Monitor control mode NAVI: Navigation system control mode AUD: Kenwood car audio system control mode 2 Volume Control button 3 Power button 4 Cursor button Selects the item when the menu screen is displayed. 5 Enter button Performs selected item when the menu screen is displayed. (page 4) 7 Video Source Select button Each time the button is pressed the monitor's picture switches as the navigation picture or the video picture set to "AV-IN". [JUST] [CINEMA] [NORMAL] English 3 Setup Menu English Setting Menu MENU 1 2 Press button. Menu screen is displayed, and the monitor enters to menu mode. MENU Press or and press ENTER VOICE button to select the adjusting item, button. "SCREEN CONTROL": Adjust the picture quality (brightness, contrast etc. ). "SETUP": Setup the picture input method and the beep sound. Screen control MENU 1 2 Press MENU button. ENTER Select "SCREEN CONTROL", and press VOICE button. 3 Press or button to select the adjusting item. (Display while displaying the picture from the NTSC signal. ) "COL": Adjusts color. (Display while displaying the picture from the PAL signal and the NTSC signal. ) "CONT": Adjusts contrast. Press or button to adjust each item. ENTER 4 5 Select "RETURN" and press to end the Menu mode. Also, the monitor exits from Menu mode by no opeation for 10 seconds. VOICE 4 English Setup MENU 1 2 Press MENU button. ENTER Select "SETUP", and press VOICE button. 3 Press or button to select the adjusting item. "NAV": Setup input and switch method of the navigation picture. Item "RGB"* "AV-IN" "OFF" Setting When Kenwood navigation system is connected by the dedicated cable. · After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. · Insulate unconnected cables with vinyl tape or other similar material. · Thoroughly wipe away oil and other dirt from the installation surface. Please avoid installation on uneven surfaces. 6 English Connection Monitor Unit AV input Audio input (MONO) AV cable (Commercially available) Navigation Unit Visual input Bundle cables with the clamper (Accessory A) Cable accompanying the Navigation System When you connect the Mute Cable to the Navigation System, the voice of the Navigation guide will interrupt. Mute cable (Brown) NAVI MUTE Car fuse box (Main fuse) Ignition key switch Fuse (2A) ACC ACC Connect TEL mute cable of the navigation system. Ignition cable (Red) +12V 2CAUTION +12V For the sake of safety, be sure to connect the parking sensor. PRK SW Battery Ground cable (Black) To car crassic Parking sensor cable (Green) English 7 Installation English Installation for Monitor Unit Installation location and cleaning Select for installation a location where the stand can be placed completely horizontal or where the front edge of the support (petal-shaped part) can be attached horizontally as shown in Figure A. Do not install in locations where the entire support is at a diagonal such as in Figure B or where the monitor unit is facing down such as in Figure C. 2CAUTION A B C Thoroughly wipe away and dust or grease from the installation location using a cloth which has been soaked in a neutral cleaning agent and wrung out. 1 Install the shoe on the rear of the TV monitor temporarily using the supplied hexagon wrench (Accessary C). NOTE When adjusting the fixing screw of the shoe, use the hexagon wrench (Accessary C) that came with the product. 2 Bend the stand support to conform to the shape of the installation location. 3 Adjust the shape of the support so that there is no rattling or gap when the stand is placed on the support. 4 Peel off the protective strip from the double-sided tape on the bottom of the stand and securely attach the stand. 2CAUTION Shoe · Do not attach the double-sided tape more than once or touch the adhesive with your fingers as this will weaken its adhesive strength. [. . . ] Before calling service, first check the following table for possible problems. · The unit is not connected to the parking brake detection switch. · For safety reasons no video picture are displayed while the vehicle is moving. · After checking for short circuits in the cables, replace the fuse with one having the same rating. [. . . ]