User manual KENWOOD KMD-X91

[. . . ] · Make sure not to get your fingers caught between the faceplate and the unit. · Be careful not to drop the unit or subject it to strong shock. · Do not touch the liquid crystal fluid if the LCD is damaged or broken due to shock. The liquid crystal fluid may be dangerous to your health or even fatal. [. . . ] Play starts at the beginning of the displayed track number. NOTE (For disc changers) Pressing the 4 button whilst listening to track 1 only searches back to the beginning of that track. The reverse search is not "recycled" to the last track on the disc. Making a Forward Track Search: Press the ¢ button to display the desired track number. Press once to fast forward to the next track, twice to fast forward to the track after that, and so forth. NOTE (For disc changers) You cannot make a forward track search when listening to the last track on a disc. Fast Forwarding and Reversing Disc Play Fast Forwarding Disc Play: Hold down on the ¢ button. Release your finger to play the disc at that point. -- 16 -- Disc Search (Function of disc changers) Search forwards or backwards through the discs in a disc changer until you reach the one that you want to listen to. Making a Reverse Disc Search: Press the DISC­ button to display the desired disc number. Each time the button is pressed, the displayed disc number decreases by one. Making a Forward Disc Search: Press the DISC+ button to display the desired disc number. Each time the button is pressed, the displayed disc number increases by one. Play starts at the beginning of the displayed disc. NOTE Track Scan Successively play the beginning of each track on a disc until you find the track that you want to listen to. Starting the Track Scan: Press the SCAN button. "Scan/T-Scan ON" is displayed and the first 10 seconds of each track are played, and the tracks are played in order. The cursor blinks in the position where character input can be made. 6 Press the NAME. S button. The disc name is stored and the disc name preset mode is cancelled. If you make no entry in a 10-second period, the name will be stored with the characters input so far. NOTE 3 Press either the 4 or ¢ button to move the cursor to the desired position. The 4 button moves the cursor to the left, and the ¢ button to the right. 4 Each time the TI button is pressed, the characters to be entered change as listed below. Alphabet (upper case): A ~ Z Alphabet (lower case): a ~ z Numerals and symbols: 0~9 @ " ` ` % & +-=, . /\<>[] · The number of characters and discs whose names can be stored will differ depending on the disc changer that is connected. · Discs are identified by their total length and number of tracks. If another disc happens to have the same specifications as one that you have already stored a name for, the name will be displayed for it, too. · If you want to change the name of a disc, repeat steps 1 and 2 to display the name, and then repeat steps 3 and 4 to input the changes. · Pressing the reset button does not erase the disc names stored in a disc changer. Special characters: á à é è í ì ó ò ú ù Ñ Ç ® ß < fl â ä ê ëîïôöûüñç©Æ>fi NOTE The operation and characters that can be entered may change as listed below, depending on the unit that is connected. A press of the TI button exits the disc name preset mode. -- 20 -- Menu settings Menu System You can set the defaults for additional functions in the menu mode. Make a setting for each function, referring to the following operations. SRC KMD-X91 PWR OFF PTY DISC + 1 Enter the menu mode Hold down the MENU button for one second or more. The function that you can adjust is indicated with the current settings displayed. FM MENU AUD LOUD SCAN RDM REP D. SCN M. RDM TI VOL ADJ CLK NAME. S AM DISC - ATT 1 2 3 4 5 6 2 Selecting function to set Press the FM button to search through the functions until you see the one you want to adjust in the display. [. . . ] The antenna control cable is not connected. Radio reception is poor. The memory is erased when the ignition is turned off. The battery cable has not been connected to the proper terminal. The ignition and battery cable are incorrectly connected. The TEL mute function does not work. The TEL mute function turns on even though the TEL mute cable is not connected. The TEL mute cable is not connected properly. The TEL mute cable is touching a metal part of the car. -- 31 -- Troubleshooting Guide MD/External disc control mode English PROBLEM The MD cannot be inserted. [. . . ]