User manual KENWOOD KMD-D400

[. . . ] · To prevent deterioration, do not touch the terminals of the unit or faceplate with your fingers. · Do not subject the faceplate to excessive shock, as it is a piece of precision equipment. · During installation, do not use any screws except for the ones provided. The use of improper screws might result in damage to the main unit. The marking of products using lasers (Except for some areas) Cleaning the Unit If the front panel gets dirty, turn off the power and wipe the panel with a dry silicon cloth or soft cloth. CLASS 1 LASER PRODUCT The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. [. . . ] If no disc is present in the stack position: The 0 button corresponding to the disc number glows green. · An MD cannot be inserted while the operation indicator is red. · When an MD is inserted, it will be stored as the smallest available disc number. For example, if disc No. 1 and disc No. 2 are both empty, the inserted disc will be denoted as disc No. 1. To play an MD: Select the disc changer mode on the centre unit. NOTE When an MD has been stored in the stacker, the unit will enter one of the states listed below, depending on the type of centre unit connected. Centre units brought on to the market in 1998 or earlier: The system will remain in the disc play STOP state. Centre units brought on sale in 1999 or later (certain models excluded): The system will switch to the tuner mode. To eject an MD: Press one of the 01 - 03 buttons depending on the disc you want to remove. NOTE The 0 button with the disc number corresponding to the MD currently being ejected will blink green. NOTE · If your system is connected to a centre unit brought on to the market in 1999 or later (excluding certain models), it will automatically switch to MD play mode when the first MD is inserted, even if there are other sources. · The 0 button with the disc number corresponding to the MD currently playing will blink red. To switch the MD: Select the disc number using the DISC+ or DISC- button on the centre unit. Disc No. 1 being played: the indicator blinks Disc No. 2 being played: the indicator blinks When the O-N switch is set to "O", the phrase "NO NAME" will be displayed if the centre unit display is switched accordingly, but the DNPS (Disc Name Pre-Set) function cannot be used on the MD in the main unit. --6-- Plus-one MD play Even when three MDs have been set in the main unit, a further MD can be played as the plus-one MD. Switching Spectrum Analyzer Display You can select the display to enjoy sounds with eyes. To play a plus-one MD (a fourth MD): 1 Press one of the 01 - 03 buttons for at least one second. The MD currently set in the play position will now be stored in the stack position. Operation for "N" Setting: Each time you press the DISP button, the spectrum analyzer display switches as follows; Operation for "O" Setting: 2 Insert the MD in the MD slot. The disc is then set in the play position. The and the disc begins to play. NOTE indicator blinks 1 Selecting MD play source mode. 2 Each time you press the DISP button, the spectrum analyzer display switches as follows; w · While the plus-one MD is being played, the buttons 01 to 03 will blink red. · An MD cannot be inserted when the operation indicator is red. · When a plus-one MD has been set in the main unit, the disc cannot be changed or the disc scan switched ON/OFF from the centre unit, nor can random magazine playback be switched ON/OFF from the centre unit. · While the plus-one MD is playing, the disc repeat function will operate, but it cannot be cancelled from the centre unit. To remove the plus-one MD: Press one of the 01 - 03 buttons. NOTE 1 "SCAN MODE ON":Displays 2 to 0 areautomatically shown in succession for about five seconds each. w 2 "PEAK HOLD" w 3 "LASER" w 4 "H-SCOPE" w 5 "FIREWORKS" w 6 "SQUASH" w 7 "V-SCOPE" w 8 "BLIZZERD" w While the plus-one MD is being ejected, the buttons 01 to 03 will blink green. 9 "KISS" w 0 "SIDE WAVE" w !"SPEANA OFF":Spectrum analyer off. NOTE · The spectrum analyser name is not shown while the disc title or track title is being displayed. · During operation 1, the DEMO indicator will light. --7-- Operations English Menu System To accommodate a greater number of functions, a function set system has been employed for making settings. Press the DISP button to enter the function set mode and then display the function to make the setting. Table of Adjustment Mode Adjustment mode (Display) Selectable title*1 ("TITLE") Title scroll*2 ("SCROLL") Spectrum Analyzer level*3 ("ANA LV") LCD contrast level*4 ("LCD CNT") Selectable Illumination ("COLOR") NOTE Operation of Control button DISC+ button DISC- button 1 Selecting MD play source mode. 2 Press the DISP button for at least one second, enter the function set mode. £ Analyzer title ("ANA") £ Disc title("DISC")£ £ Track title ("TRACK") £ 3 Press either the 4 or ¢ button on the centre unit. Each time the button is pressed, the adjustment mode will change as follows: Automatic scrolling ("AUTO") £ Off ("OFF") The spectrum analizer level increased. The setting values higher. "MENU TITLE" (Selectable title)* 1 5 5 5 5 5 The spectrum analizer level decreased. "MENU SCROLL" (Title scroll)*2 "MENU ANA LV" (Spectrum analyzer level)* 3 "MENU LCD CNT" (LCD contrast level)*4 "MENU COLOR" (Selectable Illumination) The setting values lower. 4 Press the DISC+ or DISC- button on the centre unit. Look at the table to adjust the mode being displayed. Green("GREEN")£Amber("AMBER") 5 Press the DISP button to end the function set mode. *1: The spectrum analyser name is not shown while the disc title or track title are being displayed. [. . . ] The system will not enter the Menu mode. The computer chip in the unit is not functioning normally. The insertion orientation of the MD is incorrect or the MD is upside down. The system is not in MD play mode. -- 13 -- Troubleshooting Guide The following messages are displayed on the centre unit when certain problems are occurring in your system. Take the recommended actions. English NO PANEL E-30 BLANK NO TRACK E-99 E-0d HOLD The faceplate of this unit has been removed. [. . . ]