User manual KENWOOD KDC-234SG

[. . . ] • When replacing a fuse, only use a new fuse with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction. If you use the wrong screws, you could damage the unit. Do Not Load 3-in. CD with its adapter into the unit, the adapter might separate from the CD and damage the unit. English | 3 B64-3245-00_E_English. indd 3 05. 8. 2 5:25:18 PM Notes • If you experience problems during installation, consult your Kenwood dealer. [. . . ] The faceplate unlocks, allowing you to detach it. • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. • Do not expose the faceplate to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Adjusting Clock 1 Enter Standby Press the [SRC] button. Select the "STBY" display. Reattaching the Faceplate 2 Select the clock display Press the [CLK] button. 1 Align the projections on the unit with the grooves on the faceplate. 3 Enter clock adjustment mode Press the [CLK] button for at least 2 seconds. Projections Grooves 4 Adjust the hours Push the Control knob towards [FM] or [AM]. Adjust the minutes Push the Control knob towards [4] or [¢]. 2 Push the faceplate in until it clicks. The faceplate is locked in place, allowing you to use the unit. 5 Exit clock adjustment mode Press the [CLK] button. TEL Mute The audio system automatically mutes when a call comes in. When a call comes in "CALL" is displayed. The "CALL" display disappears and the audio system comes back ON. The "CALL" display disappears and the audio system comes back ON. English | 9 B64-3245-00_E_English. indd 9 05. 8. 2 5:25:21 PM Tuner features Control knob MONO SRC 1–6 Band display Frequency display AUTO indicator ST indicator Preset station number Monaural indicator Tuning Selecting the station. Tuning Mode Choose the tuning mode. Each time you press the knob, the Tuning mode alternates between the modes shown in the table below. Tuning mode Display Operation Auto seek "AUTO 1" Automatic search for a station. indicator Preset station seek "AUTO 2" Search in order of the stations indicator in the Preset memory. Manual — Normal manual tuning control. 1 Select tuner source Press the [SRC] button. Select the "TUnE" display. 2 Select the band Push the Control knob towards [FM] or [AM]. When the Track Repeat is ON, the "REP" indicator is ON. Scan Play Playing the first part of each song on the disc you are listening to and searching for the song you want to hear. 1 Start Scan Play Press the [SCAN] button. "SCN" indicator is ON. 2 Release the button when the song you want to hear is played Press the [SCAN] button. Random Play Playing all the songs on the disc in random order. When the Random mode is ON, the "RDM" indicator is ON. • When you push the Control knob toward [¢], the next random song starts. English | 13 B64-3245-00_E_English. indd 13 05. 8. 2 5:25:22 PM Accessories/ Installation Procedure Accessories 1 . . . . . . . . . . 1 2 . . . . . . . . . . 2 3 . . . . . . . . . . 1 • If the power is not turned ON (or it is ON, but will be OFF immediately), the speaker wire may have a short-circuit or touched the chasis of the vehicle and the protection function may have been activated. • If your car is not prepared for this special connectionsystem, consult your Kenwood dealer. • Only use antenna conversion adapters (ISO-JASO) when the antenna cord has an ISO plug. • Make sure that all wire connections are securely made by inserting jacks until they lock completely. • If your vehicle’s ignition does not have an ACC position, or if the ignition wire is connected to a power source with constant voltage such as a battery wire, the power will not be linked with the ignition (i. e. , it will not turn on and off along with the ignition). If you want to link the unit’s power with the ignition, connect the ignition wire to a power source that can be turned on and off with the ignition key. • If the fuse blows, first make sure that the wires have not caused a short circuit, then replace the old fuse with one with the same rating. [. . . ] ☞ Connect the wire correctly, referring to the section on <Connecting Wires to Terminals>. English | 19 B64-3245-00_E_English. indd 19 05. 8. 2 5:25:25 PM Troubleshooting Guide Disc source ? The specified disc does not play, but another one plays instead. ☞ Eject the disc magazine and check the number for the specified disc. ☞ Clean the CD, referring to the CD cleaning of the section on <About CDs> (page 5). ✔ The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF. [. . . ]