User manual KENWOOD HTB-S715DV

[. . . ] Using the large black screws, attach the speaker bases to the bottoms of the speakers as shown in the diagram below. 12" of speaker wire through the hole in the rear of the base, then up through the hole in the base's bottom, as shown in the diagram below. · Use the wire with the white bands for the left speaker; use the wire with the red bands for the right speaker (see the large diagram to the right). Important: Do not plug the receiver's power cord into an AC outlet until you have properly connected all of the speakers. Connect the speakers as shown in the large diagram to the right. [. . . ] If you use a Component Video cable to connect the DVD player to the receiver you must also use a Component Video cable to connect the receiver to the TV or monitor. Matching the Receiver to the Speaker System Your receiver has circuitry that tailors its performance for different speaker types, overcoming the mis-match that is common between subwoofers and satellite speakers. After performing this adjustment, dialog spoken by male actors as well as music will sound more natural and life-like on your HTB-S715DV system. Press the > MULTI CONTROL button repeatedly until the display reads "SP SETUP", then press the ENTER button. Press the > "HTB3 6. 1CH". MULTI CONTROL DVD Player Connections button repeatedly until the display reads MULTI CONTROL button repeatedly until the display reads "OK", then 4. The receiver's electronics are now matched to your HTB-S715DVDV system's speakers. Balancing the Speakers Your receiver comes with the speaker volume settings pre-balanced. If you have positioned the speakers as shown in the diagram your system will create a spacious surround sound environment right out of the box with no further adjustment required. If your room is arranged differently than shown in the diagram, or if you simply want to fine-tune your system's performance, you can easily change the volumes of the individual speakers to get a better balance: 1. Press the > MULTI CONTROL > Connecting a Video Game to the Front-Panel Game Input Your HTB-S715DV receiver has a set of inputs specially-designed for video games. The inputs are located behind a flip-down door on the receiver's front panel. · Connect your game console's video and audio outputs to the inputs labeled "GAME" (see diagram to the right). MODE 1 activates the following functions: · The receiver will detect whenever the game console is turned on and will automatically switch its input to GAME. · The receiver will automatically activate special EQ circuitry (Active EQ -- EQ GAME) that is designed to enhance game sounds. · The listen mode will automatically switch to Dolby Pro Logic IIx: Game, or the appropriate digital surround mode. (Note: If you change to a different listen mode, that mode will be automatically activated the next time you select the GAME input. ) 4. In MODE 2 the receiver will detect whenever the game console is turned on and will automatically switch its input to GAME. FM 75 COMPONENT VIDEO OUTPUT COMPONENT VIDEO INPUT ASSIGNABLE SPEAKERS (6 ­ 8) ASSIGNABLE Y CB CR COAX 2 ANTENNA DIGITAL IN ASSIGNABLE IN2 IN1 VIDEO IN VIDEO IN VIDEO OUT VIDEO IN MONITOR OUT + L + ­ CENTER SURR BACK /SW R SURR L OPT 1 OPT 2 Y GND AM CB CR ­ R FRONT L COAX 1 SUB WOOFER SURROUND BACK PRE OUT IN DVD PLAY IN REC OUT PLAY IN VIDEO 2 VIDEO 1 IN AUX R button once. The display will read "TEST TONE" and then change to "AUTO". MULTI CONTROL 5. Press the ENTER button repeatedly until the speaker you want to adjust appears on the display. The speaker's icon will flash and you will hear test noise through the speaker. [. . . ] To operate the DVD player with the receiver's remote, press the DVD button, then press the button for the operation you want to perform, as shown in the diagrams to the right: DVD button DVD power ON/OFF Numeric entry buttons Cursor and selection controls Activates the Subtitle function Pages down or up Using the Dual-Source/Single-Zone mode You can listen to a game soundtrack through headphones while others listen to music through the system's speakers. Press the DUAL SOURCE INPUT button to select either the GAME input or the F. · Video from the selected input will show on a connected TV or monitor. [. . . ]