User manual KENWOOD 600 SERVICE MANUAL

[. . . ] Condensation: When the car is airconditioned, moisture may collect on the laser lens. This unit can only play the CDs with: WARNING Stop the car before operating the unit. Basic operations Getting started Canceling the display demonstration Setting the demonstration mode Adjusting the clock 5 6 Listening to the radio Adjust [SETTINGS] mode settings 6 8 Listening to a disc Selecting Repeat Play Selecting Random Play Selecting Scan Play Selecting a folder/track/file Listening to the other external components 9 Function settings Troubleshooting Installation/connection Basic procedure Warning Caution Wiring connection Installing the unit 10 11 12 The illustrations in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the illustrations may differ from what appears on the actual equipment. If you experience problems during installation, consult your Kenwood dealer. [. . . ] If [ON] is selected, display demonstration starts if no operation is done for about 20 seconds. 4 Hold to finish the procedure. Adjusting the clock 1 Press the volume knob to enter [FUNCTION] mode. 5 Turn the volume knob to adjust the hour, then press to enter minute adjustment. 7 Hold to finish the procedure. Setting the demonstration mode 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select [DEMO MODE], then press to enter. Listening to the radio Hold to turn on or off the Traffic Information function (not applicable if "MW/ LW" is selected). Hold for about 2 seconds to memorize the current station or the selected Program Type. (Refer to [PTY SEARCH] on page 7 to select the Program Type. ) Press briefly to recall memorized station (or Program Type after entering the PTY search mode). 6 Adjust [SETTINGS] mode settings While listening to the radio. . . Item LOCAL SEEK SEEK MODE Selectable setting (Preset: *) ON: Searches only FM stations with good reception. AUTO MEMORY YES: Automatically starts memorizing 6 stations with good reception. (Selectable only if [NORM] is selected for [PRESET TYPE]. ) (page 4) MONO SET ON: Improves the FM reception (but the stereo effect may be lost). Turn the volume knob to select the PTY language (ENGLISH */ FRENCH/ GERMAN), then press to confirm. NEWS SET 0M ­ 90M: Sets the time for receiving the next news bulletin. TRE ADJUST TRE C FRQ: 10. 0K/ 12. 5K */ 15. 0K/ 17. 5K: Selects the center frequency. BALANCE L15 -- R15 (Preset: 0): Adjusts the left and right speaker output balance. FADER R15 -- F15 (Preset: 0): Adjusts the rear and front speaker output balance. DETAIL SET LPF SUB-W: THROUGH *: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/ 160HZ: Frequencies higher than 85 Hz/ 120 Hz/ 160 Hz are cut off. SUB-W PHASE: REV (180°)/ NORM (0°) *: Selects the phase angle of the subwoofer output to be in line with the speaker output for optimum performance. (Selectable only if a setting other than [THROUGH] is selected for [LPF SUB-W]. ) SUPREME SET: ON *: Creates realistic sound by interpolating the high-frequency components that are lost in MP3/WMA audio compression. (Selectable only when playback an MP3/ WMA disc. ) VOL OFFSET: ­8 -- +8 (for AUX) ; ­8 -- 0 (for other sources): Presets the volume adjustment level of (Preset: 0) each source. The volume level will automatically increase or decrease when you change the source. (Before making an adjustment, select the source you want to adjust. ) 600/ KDC-3051G/ KDC-315A/ KDC-315R/ KDC-3251RY only: [SUB-W LEVEL/ SUB-W SET/ LPF SUB-W/ SUB-W PHASE] is selectable only if [SWITCH PRE] is set to [SUB-W]. (page 4) [SUB-W LEVEL/ LPF SUB-W/ SUB-W PHASE] is selectable only if [SUB-W SET] is set to [ON]. [. . . ] If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. Make sure the faceplate will not hit the lid of the console (if any) when closing and opening. After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. If the fuse blows, first make sure the wires aren't touching to cause a short circuit, then replace the old fuse with one with the same rating. [. . . ]