User manual KENMORE ELECTRIC ROTARY SEWING MACHINE

[. . . ] Make sure the microwave hood will be mounted against and supported by both a flat, vertical wall and upper Support for weight of 150 pounds, which includes microwave hood combination and items placed in the oven and upper cabinet. Make sure the microwave hood will be attached with two lag screws to a minimum of one, vertical 2" x 4" wall stud. Make sure not to mount the microwave hood to an island or peninsula cabinet. Gloves Safety glasses Measuring tape Pencil Masking tape or thumb tacks Scissors Electric drill 3/16" drill bit 3/8" and 3/4" wood drill bits Flat-bladescrewdriver Phillips screwdrivers: No. [. . . ] Ground prong terminal para conexibn a tierra \\ \ 3-prong ground-type wall receptacle tomacorriente de pared con tres terminales para puesta a Uerra For your personal safety, this appliance must be grounded. This appliance is equipped with a power supply cord having a 3-prong ground plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong groundtype wall outlet, grounded in accordance with the National Electrical Code, ANSI/NFPA70 -- latest edition*, and all local codes and ordinances. CAUTION: To reduce risk of fire and to properly exhaust air, be sure to vent air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces or garages. Continued frompage7 Forwall or roofventing methods: Choose between roof venting or wall venting. If the wall exhaust method is chosen, be sure that there is proper clearance within the wall for the exhaust vent. V' that length of vent and number of elbows should be kept to a minimum to provide efficient performance. V' using caulking compound to seal exterior wall or roof opening around cap. NOTE: If flexible metal vent must be used, calculate each foot of flexible metal vent as two feet of rigid metal vent. The total length of the vent system including straight vent, elbow, transitions, wall or roof caps must not exceed the equivalent of 140 feet of 3-1/4" X 10" rectangular or 6" diameter round vent. The "rear wall" arrows mustbe againstthe rear wall sothat the holes cut in the cabinetbottomand the holes in the top of the microwavecabinetwill align. If the cabinet bottom has a frame around it, trim the template edges so that the template fits inside the frame against the cabinet bottom. Important:The 10-7/16" dimension from the rear wall to holes "J" and "K" mustbe maintained. Checkif points "D" and "E", or "F" and %" on wall templateare over a wall stud @: If points are over a wall stud, drill 3/16" holes. If thereis not a wall stud at points "D" and "E", or "F" and "G" or at only one set of points, find within shadedareas"H" and 'T' the screw points closest to the center of wall stud(s). Two or preferablyfour lag screws must be usedto secure mounting plateto wall. Use a hole drill or key hole saw to cut a 2" diameter hole at shaded area marked "M" on upper cabinet template. Note: Install a power supply cord bushing around hole if cabinet is metal. These are for 2, 1/4-20 x 3" round head bolts and washers used to secure microwave hood to upper cabinet. Keepdamper assembly for use if microwave hood is ever vented through wall or roof. If venting throughthe roof, drill 3/4" hole in one corner of shaded rectangular area marked "L" on upper cabinet template. [. . . ] Push damper assembly @ through opening in mounting plate @ so that tabs in damper assembly lock damper assembly against mounting plate. Excessive Weight Hazard Use two or more people to move and install microwave hood. Carefully lift microwave hood and hang it on support tabs ® at the bottom of mounting plate. Thread power supply cord through the power supply cord hole in the bottom of the upper cabinet, Push microwave hood against mounting plate until locking latch @ snaps into microwave hood. [. . . ]