User manual KENMORE 625.393760

[. . . ] OWNER'S MANUAL Water Softeners With High Performance Valve MODEL NOS. IntelliSoft 370 Series 625. 383760 IntelliSoft 370 Series 625. 393760 Caution: Read and follow all safety rules and operating instructions before first use of this product. Questions ?Visit www. KenmoreWater. com or call toll free 1-800-426-9345 (M - F, 7AM - 8 PM CST) Repair or Parts ?Call toll free 1-800-366-7278 See back cover for other Sears service numbers. [. . . ] Press the SET LOW SALT LIGHT button until a (*) shows opposite this number. In the example, the light will come on when the stored salt drops to level 2. If you wish to turn the salt monitor off, press the SET LOW SALT LIGHT button until OFF shows above. NOTE: Your salt monitor is an estimate of your salt level; accuracy depends on the type of salt used and other regeneration characteristics. ADDING SALT TO STORAGE TANK The Salt Monitor System will turn the low salt light on to warn you when to refill with salt. Check for a low salt light a few weeks after you install the softener, and every week after that. Note: You will have a loss in softening capacity and may get partly hard water if less than 10 inches (salt monitor level 2) of salt is in the storage tank. Questions?Call The Kenmore Water Line 1-800-426-9345 22 Faceplate Timer Features OPTIONAL SETTINGS: · SALT EFFICIENCY · CLEAN FEATURE · CLEAN FEATURE MINUTES · INTELLISOFT 97% FEATURE · 12 / 24 HOUR CLOCK · GALLONS / LITERS · MAXIMUM DAYS BETWEEN REGENERATIONS 1. To set any of the following options, press and hold SELECT1 for 3 seconds until 000 shows in the display Then press once until the SALT EFFICIENCY display shows. When this feature is ON, the unit will operate at salt efficiencies of 4000 grains of hardness per pound of salt or higher, which will reduce the softeners salt usage. When installing this unit in the State of California, this setting MUST be ON. California Efficiency Requirement Your Kenmore Water Softener has a "High Efficiency" feature with an "ON" or "OFF" setting. This softener setting is shipped in the "OFF" position, which utilizes the maximum rated capacity while most often achieving maximum salt efficiencies. When installing this unit in the State of California, you MUST turn this setting to the "ON" position which may initiate more frequent recharges, however it will operate at 4000 grains per pound of salt or higher. This feature is beneficial on water supplies containing iron and/or high amounts of sediments (sand, silt, dirt, etc. ). When set to ON, a backwash and fast rinse cycle will occur first, preceeding the normal regeneration sequence (see pages 26 - 28). This provides extra cleaning of the resin bed before it is regenerated with the salt brine. To conserve water, if your water supply does not contain iron or sediments, be sure this feature is set to OFF. Clean feature minutes: If you are using this feature, the length of the extra backwash cycle automatically is set to 3 minutes. To change this cycle time, use the UP button to increase, the time, or the DOWN button to shorten the time. If no change is desired, continue to next step. SALT SIGNAL LEVEL LEVEL SALT SIGNAL LEVEL LEVEL SALT SIGNAL LEVEL LEVEL SALT SIGNAL LEVEL LEVEL 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 FIG. 37 SALT SIGNAL LEVEL LEVEL MIN SALT SIGNAL LEVEL LEVEL MIN 8 7 6 5 4 3 2 1 CLEAN TIME 8 7 6 5 4 3 2 1 CLEAN TIME Default Minutes Example: Time Set to 7 Minutes FIG. Call The Kenmore Water Line 1-800-426-9345 23 Faceplate Timer Features 4. [. . . ] 625. 383760 and 625. 393760 7 8 2 3 4 5 9 6 10 Rating Decal Location 1 31 11 12 30 29 13 28 27 14 15 16 17 18 23 26 25 24 22 19 21 20 Questions?Call The Kenmore Water Line 1-800-426-9345 42 Parts List Kenmore MODEL Nos. 1 1 2 3 -- 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Part Number ------7284304 7284231 7284338 7088033 7176292 7141001 7288560 7275907 7284540 7284532 7284639 7252268 7286021 7265025 7219888 7082150 7003847 7100819 7137913 7287140 7284613 0900431 1103200 9003500 7239155 7105047 0502272 7287182 7170270 7077870 7170254 7170296 3442699 7287213 7282603 Part Description Cover Lock (Required for shipping only) Rim Insert (Required for shipping only) Cover (main) Salt Hole Cover (order following decal) Instruction Decal Clamp Retainer (2 required) Clamp Section (2 required) Vapor Barrier Timer Repl. (PWA) Transformer, 24 V - 10 VA Faceplate (order following decal) Faceplate Decal Rim (includes key no. [. . . ]