User manual KENMORE 625.343920

[. . . ] WARRANTY IS AVAILABLE BY SIMPLY RETURNING THE WATER FILTER SYSTEM TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. 817 WA, Hoffman Estates, IL 60179 2 TABLE OF CONTENTS Water Treatment Filter Cartridges . 3 Parts of the System / Typical Installation Drawing / Tools and Materials Needed . [. . . ] Then, with the washer in place, turn the tub ing adaptor onto the valve and tighten securely. 2 Check local codes for approval SINK nut (2) ­ not req'd with all types of clamp B pre­drill 1/8" hole (iron pipe) cold water seal clamp A valve washer adaptor handle STEP 2 - MAKE HOLE FOR FILTERED WATER FAUCET Select 1 of the following places to install the faucet. Be sure there's room underneath so you can make the needed connections. If you are installing the deluxe model, be sure the electronic indicator base will fit flat against the surface. The faucet with the elec tronic indicator base requires a 1-1/8" dia. hole. CAUTION: To avoid damaging the sink, consult a qualified plumber or installer for drilling procedures in porcelain or stainless steel. Place plumbers putty around the drilled hole, to prevent water leaks around the faucet. FIG. (electronic base faucet) hole through sink or countertop plumbers putty 5 INSTALLATION STEPS STEP 3 - ASSEMBLE AND INSTALL FAUCET Note: If the faucet is not assembled, slide the lever over the cylindrical nut. Slide the chrome washer, large rubber washer and lock washer, in that order, onto the faucet stud. Using the washer, turn the tubing adaptor onto the faucet stud and tighten securely. On the underside of the sink or countertop, in sert the large steel washer between the lock washer and the bottom of the sink or countertop. 4 A MODEL 625. 343920 spout spout lever faucet screw chrome washer rubber washer (large) steel washer (large) lock washer hex nut rubber washer electronic faucet base hex nut B DELUXE MODEL 625. 343950 washer tubing adaptor B. Using the washer, turn the tubing adaptor onto the faucet stud and tighten securely. 4C, locate the faucet support and gasket over the sink or countertop mounting hole. (First, break out the small button and save for use in step G below. ) D. Place a screw into a notch in the faucet sup port, with the special nut on the underside of the mounting hole (FIG. Be sure the support is positioned correctly, then tighten both screws evenly so the support is held firmly in place. Insert the faucet stud and base leadwire through the support and mounting hole. Lower the faucet and base down onto the sup port, being careful not to pinch the leadwire. Use the 5/8" long screw to fasten the faucet base and support together. how much sediment, taste and/or odor, or other un wanted substance, is in the water Use the following information as a guide. However, no matter which type of cartridge you are using, you will know it is time to replace it when you first no tice the return of the unwanted substance in your water. [. . . ] 625. 343920 Kenmore Deluxe Undersink Drinking Water Filter System, Model No. 625. 343950 18 17 1 Saddle Valve 2 4 16 15 14 16 15 5 3 6 12 7 20 8 9 11 24 21 9 6 10 5 10 4 13 10 ÉÉ ÉÉ 14 19 22 23 REPAIR PARTS LIST KEY NO. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 z v v v v v v v v v PART NUMBER DESCRIPTION Model No. 625. 343920 625. 343950 7160453 7160453 Screw, #10 ­ 14 x 3/4" (8 req. ) 7182502 9006053 9003203 7131349 9004503 7156535 7161255 42­34385 7156577 7160437 7164936 7174961 9043201 7064144 1260600 7011272 7161263 ­­­ ­­­ ­­­ ­­­ ­­­ ­­­ 7182586 42­34360 42­34362 42­34370 42­34372 42­34365 42­34377 42­34330 42­34331 42­34334 7182502 9006053 9003203 7131349 9004503 7156535 7161255 42­34385 7156569 7160437 7164936 7174961 9043201 7064144 1260600 7011272 7161263 7161352 0900156 0900713 7163469 7115725 7162552 7182586 42­34360 42­34362 42­34370 42­34372 42­34365 42­34377 42­34330 42­34331 42­34334 Mounting Bracket (includes screws) Screw, #10 ­ 14 x 1­1/4" (2 req. ) Nut, 3/8" Tube (2 req. ) Tubing Insert, 3/8" (2 req. ) Elbow, 3/8" NPT x 3/8" Tube (2 req. ) Head Nipple, 3/8" NPT x 1 ­ 1/2" O­ring, 3­3/8" I. D. [. . . ]