User manual KELVINATOR KF820

[. . . ] WASHING MACHINE KF 820 USER MANUAL 35. 292. 792/0 Dear customer, Please read these operating instructions carefully and pay particular attention to the safety notes indicated in the first pages. We recommend that you keep this instruction booklet for future reference and pass it on to any future owners. Transport damages When unpacking the appliance, check that it is not damaged. If in doubt, do not use it and contact the Service Centre. The symbols you will see on some paragraphs of this booklet have the following meaning: The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly important for your safety or correct functioning of the appliance. The information marked with this symbol provides additional instructions and practical tips on the use of the appliance. [. . . ] Temperature selector This control allows you to select the temperature of the washing cycle in accordance with the kind of clothes to be washed. Turn the control until the required temperature coincides with the marker. On the program table you will find the most apropriate temperature for each kind of washing. This will ensure a saving in electricity consumption. 2. Spin speed selector This dial has the following positions: · = no spin for cotton · 300 = MIN, for cotton · 800 = MAX, for cotton. For synthetics, delicates and wool the maximum position corresponds to 750 rpm. The intermediate positions refer to spin speed values for cotton. 7. Program selector To select the required program turn the control clockwise until the marker on the top coincides with the letter of the required program (reference mark on the control panel). If at any chance you pass by the required letter NEVER TURN THE CONTROL ANTICLOCKWISE just continue clockwise until the required letter is reached again. 3. RINSE HOLD button (Easy iron. Pressing this button the water will hold up in the wash tub at the end of the cycle. Press again to drain the water and take out the clothes. 4. HALF LOAD button Pressing this button before starting the intense program there will be one rinse less which leads to energy and water saving. 5. On/off lamp It lights when the appliance is operating. 10 Washing hints Sorting the laundry Follow the wash code symbols on each garment label and the manufacturer's washing instructions. Mould stains: treat with bleach, rinse well (whites and fast coloureds only). Grass: soap lightly and treat with bleach (whites and fast coloureds only). Ball point pen and glue: moisten with acetone (*), lay the garment on a soft cloth and dab the stain. Lipstick: moisten with acetone as above, then treat stains with methylated spirits. Red wine: soak in water and detergent, rinse and treat with acetic or citric acid, then rinse. 11 Maximum loads Recommended loads are indicated in the programme charts. General rules: Cotton, linen: drum full but not too tightly packed; Synthetics: drum no more than half full; Delicate fabrics and woollens: drum no more than one third full. Washing a maximum load makes the most efficient use of water and energy. For heavily soiled laundry, reduce the load size. Ink: depending on the type of ink, moisten the fabric first with acetone (*), then with acetic acid; treat any residual marks on white fabrics with bleach and then rinse thoroughly. Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste. (*) do not use acetone on artificial silk. Quantity of detergent to be used The type and quantity of detergent will depend on the type of fabric, load size, degree of soiling and hardness of the water used. [. . . ] Repeat the procedure until you have completely emptied the washing machine. P1114 R0072 C0073 P1115 Detergent can also accumulate inside the drawer recess: clean it with an old toothbrush. Refit the drawer after cleaning. · To continue, unscrew the lid of the diaphragm by turning it counter clockwise and pull it out. · Remove the objects such as buttons, coins and the lint that has been accumulated in the area of the pump impeller by rotating it. · Screw the lid of the diaphragm clockwise, be sure is completely tighten. [. . . ]