User manual KAWAI MP5

[. . . ] Owner's Manual Important Safety Instructions SAVE THESE INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. AVIS : RISQUE DE CHOC ELECTRIQUE The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. - NE PAS OUVRIR. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the leterature accompanying the product. Examples of Picture Symbols denotes that care should be taken. The example instructs the user to take care not to allow fingers to be trapped. The example instructs that disassembly of the product is prohibited denotes an operation that should be carried out. [. . . ] The MIDI CC# button stops blinking and the cursor in the display moves down to the value. Note: When the selected zone is set to INT, only the following parameters can be selected. 10 70 71 76 77 78 93 Panpot Sustain Level Resonance Vibrato Rate Vibrato Depth Vibrato Delay Chorus Depth PAN STN RSN VbR VbD VbY ChD When the selected zone is set to BOTH and the internal section is selected in edit mode, the parameters not available for INT section show as " XXX". 31 6. MENU The MENU buttons allow access to the edit parameters in the MP5. This collection of settings together with other editable parameters can be stored as a SETUP. Inside each of the four zones, a multitude of features and effects can be programmed and combined together into one exciting SETUP. The menu consists of Internal parameters, External parameters and Common parameters. If a zone is set as Both, both the Internal parameters and External parameters are available for the zone. In SOUND mode, both the Int Zone parameters and the Common parameters without the inverse "S(Setup)" icon can be individually stored. (see page43) The Int Zone parameters can be stored as a SOUND of the MP5's 256 SOUNDs. The Common parameters can be stored as the initial settings in SOUND mode. Zone parameters (Int) Mode Sound Selection Damper Reso. (Int Piano only) KeyOff Effect (Int Piano only) Voicing (Int Piano only) Key Range Hi/Lo Velocity Switch On/Off Velocity Switch Value Velocity Compression Velocity Offset Zone Transpose Volume Pan Fine Tune Damper Pedal On/Off/Hold Footswitch On/Off Expression Pedal On/Off Modulation On/Off Bender On/Off Bender Range Solo On/Off Solo Mode Zone parameters (Ext) Common parameters Mode TX Channel TX PRG # On/Off PRG # TX Bank On/Off Bank Select MSB LSB Keyboard On/Off Key Range Hi/Lo Velocity Switch On/Off Velocity Switch Value Velocity Compression Velocity Offset Zone Transpose TX Volume On/Off Volume TX Controller On/Off Pan Fine Tune Damper Pedal On/Off Footswitch On/Off Expression Pedal On/Off Modulation On/Off Bender On/Off TX Bender Range On/Off Bender Range Solo On/Off Solo Mode Master Volume Left Pedal Mode M. Wheel CC# Expression Pedal CC# Footswitch CC# Temperament Stretch Tuning Caution: The edited settings will be erased when the power is turned off, or other sound is recalled. To save these settings, use the STORE procedure to save them as a SETUP. (see page43) 32 6. 1 Editing Procedure and Parameters First, press the ZONE SELECT button for the zone to be edited. Next, press the MENU buttons until the parameter you want to edit appears in the DISPLAY. When a zone is set as Both, pressing the ZONE SELECT button again will switch the menu list from Internal to External or vice versa. Since each parameter has a different value range, consult the following pages for the details. Repeat this procedure for any other parameters in any of the zones that need to be modified. (See page43 for detail) Note: Once you enter the edit mode from SETUP mode by pressing the MENU button, the mode automatically changes to SOUND mode and the SOUND SELECT buttons are used to select sounds, not SETUPs. If you exit the edit mode by pressing SOUND or SETUP buttons, your changes will be lost and the previously saved settings are recalled. 6. 2 Edit Parameters Zone parameters can be edited individually for each zone. There are two parameter groups, Internal parameter group and External parameter group. If a zone is set to Int, only Internal parameters are available for editing. If a zone is set to Ext, only External parameters are available for editing. [. . . ] The USB logo can be used only for the product which is approved by USB-IF (USB Implements Forum Inc. ) test. * Macintosh is registered trademark of Apple Computer, Inc. 60 Specifications Keyboard # of Zone # of Internal Sound Polyphony Effect 88 keys with Advanced Hammer Action IV 4 zones 256 sounds Maximum 192 7 Reverbs 22 Effects 4-band Equalizer 256 SETUPs 16 x 2 LCD w/backlight 1/4" Out (L/MONO, R) Headphones MIDI IN/OUT/THRU USB (to Host) Foot Controller Damper EXP (Assignable) Foot Switch (Assignable) AC Inlet 15W Internal Memory Display Jack Power Consumption Dimensions (WxDxH) 1356 x 340 x 172 mm (53 3/8" x 13 3/8" x 6 7/8") Weight 20. 5kg(45 lbs) Accessories included Damper Pedal [F-10H] Music Rack Power Cable Owner's Manual * Specifications subject to change without notice. 61 MP5 MIDI Implementation Contents 1. Recognized data 1. 1 Channel Voice Message 1. 2 Channel Mode Message 1. 3 System Real time Message 2. Transmitted data 2. 1 Channel Voice Message 2. 2 Channel Mode Message 2. 3 System Real time Message 3. [. . . ]