User manual KAWAI FS750

[. . . ] shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from improper use of this product. Please read the following items before use This Case is a precision device designed for use at a water depth within 40 m. Please use the Case correctly after sufficient understanding of the contents of this manual in regard to handling of the Case, checks before use, maintenance, and storage after use. The Case must be used in combination with the separately available Waterproof Port. shall in no way be responsible for accidents involving immersion of a digital camera in water. [. . . ] Align the Waterproof Port with the position where the camera lens will be when the camera is loaded in the Case. Before using, always perform the following advance checks. Check the waterproof parts of the Case Check the waterproof parts of the Case as described below. 1 Ensure that the Case's O-rings are firmly attached and secured with the slide lock and the open/close dial. 2 Ensure that the separately available Waterproof Port is installed correctly, and that the Waterproof Port is attached firmly to the O-ring between the Waterproof Port and Case. 3 Ensure that the O-ring of the TTL connector is attached firmly and that the cap is screwed into the connector without loosening. Advance check 1 Before loading the digital camera in the Case, immerse the empty Case to confirm that there is no water leakage. When it is difficult, water leakage can be checked by referring "Water Leakage Test" (P. 19). · Forgetting to install the O-ring · Part of an O-ring or an entire O-ring is outside the specified groove. · O-ring damage, cracks, deterioration or deformation · Sand, fibers, hair or other foreign matter sticking to the O-ring, the O-ring groove or the O-ring contact surface. · Attached strap or silica gel getting caught when closing the Case. CAUTION: If the advance test should show water leakage with normal handling, stop using the Case and contact your dealer or an Olympus service station. En EN 10 3. How to connect the electronic flash Connecting the underwater optical fiber cable To connect the UFL-2 underwater flash (optional) to the Case using an underwater optical fiber cable (optional), follow the procedures below. How to connect the underwater optical fiber cable 1 Remove the cap of the optical fiber cable insertion slot. 2 Put the underwater optical fiber cable plug all the way into the optical fiber cable insertion slot. Setting of the digital camera 1 Set the RC mode of the camera to ON so that the camera's built-in flash is activated. Remove the eyecup from the digital camera. To improve the view of the pickup viewfinder, remove the camera's eyecup before loading it in the Case. The eyecup removed from the camera can be stored in the camera table. CAUTION: In case the digital camera is loaded in the Case without removing the eyecup and the rear lid of the Case is closed, the pickup viewfinder pops out. Remove the filter from the digital camera The digital camera cannot be loaded in the Case while the filter is attached to the lens. EN 14 Open the Case 1 Slide and hold the slide lock towards the arrow direction (1) and turn the open/close dial counter clockwise (2). 2 Turn the open/close dial to the position where it cannot be turned further. 3 Open the rear lid of the Case gently. Slide lock 1 2 CAUTION: Do not exert too much force while turning the open/close dial. Doing so may damage the dial. Attach the digital camera to the camera table In order to load the camera into the Case, attach the camera table (located on the front-lid side of the Case) to the digital camera. 1 The eyecup and the hot shoe cover of the digital camera can be stored in the camera table. 2 Attach the camera table to the tripod seat section on the bottom of the digital camera. Use the camera's tripod screw hole for attaching. En 3 The camera table has fixed up-down and front-rear orientations. To ensure that it is properly attached, refer to the illustration on the right. Up Front Down Rear EN 15 Insert the digital camera in the Case 1 Pull out the zoom dial and mode dial on the Case (pulling out the mode dial also pulls up the power switch lever) so that they do not get in the way while loading the digital camera. At this time, set the orientation of the power switch lever as shown below. 2 After attaching the camera table to the digital camera, slide the camera table into the Case's camera table-loading groove. Slide it in gently while checking that the digital camera does not interfere with the internal parts of the Case. En 3 Gently push the Case's zoom dial and mode dial down and confirm that the zoom dial can smoothly control zooming, the power switch lever can turn the digital camera ON/OFF, and that the mode dial can control the mode dial of the camera. EN 16 CAUTION: · Before loading the digital camera, attach the zoom and focus gears to the Case's zoom and focus rings. [. . . ] Independent of the number of times the Case is used, it is recommended that the O-ring should be replaced by a new piece at least once a year. · Deterioration of the O-ring is accelerated by the usage conditions and the storage conditions. Replace the O-ring even before a year has passed if it shows signs of damage, cracking or loss of elasticity. CAUTION: · Please use genuine Olympus silicone grease, silica gel and O-ring. [. . . ]