User manual KAWAI ES1

[. . . ] 10 11 11 11 12 12 13 14 15 15 16 16 17 17 18 20 21 ­2­ Important Safety Instructions SAVE THESE INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. AVIS : RISQUE DE CHOC ELECTRIQUE The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. - NE PAS OUVRIR. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the leterature accompanying the product. Examples of Picture Symbols denotes that care should be taken. The example instructs the user to take care not to allow fingers to be trapped. The example instructs the user to remove the power cord plug from the AC outlet. Read all the instructions before using the product. [. . . ] Fasten the piano and the stand with four bolts (F). CAUTION: Be sure to secure the piano to the stand with the screws. If you fail to do so, the unit could fall from the stand causing damage or personal injury. 4. Insert the pedal connection cord that comes from Pedal Board (C) into the piano's pedal jack and fasten with cord clamps. Bottom View (H) 5. Turn the Adjuster (installed on the bottom of C) until it touches the floor to support the pedal board. ­7­ PART NAMES VOLUME SLIDER (A) Move the volume slider to the right to increase the instrument's volume. Seven musical pieces will be played back randomly until the DEMO button is pressed again to stop. To select a specific demo, press the desired TONE button while the demo is playing. TONE BUTTON (C) Select the desired instrument by pressing the appropriate button. REVERB BUTTON (D) This button adds reverb to any sound which enhances the tonal quality and improves the acoustical realism. FUNCTION SECTION (F) Use these buttons to select a touch type, transpose the keyboard, or control other features (including MIDI functions). FRONT PANEL A B C D E F G ­8­ SOFT PEDAL ( H) Pressing this pedal softens the sound and also reduces its volume. * The soft pedal can be used as the sostenuto pedal by turning on the power while depressing this pedal. (2) To adjust the tempo, press the VIBRA-PHONE button while holding down the TOUCH and TRANSPOSE buttons to make the tempo slower or press the STRINGS button while holding down the TOUCH and TRANSPOSE buttons to make the tempo faster. (3) To turn off the metronome function, press the TOUCH and TRANSPOSE buttons at the same time and the metronome will stop. 2. The song will be played back using the same tone (sound) with which it was recorded. If you do not press the PLAY/ STOP button, playback will automatically stop when the song is finished. Before pressing the PLAY/STOP button, press the VIBRAPHONE button while holding down the TOUCH and TRANSPOSE buttons to make the tempo slower or press the STRINGS button while holding down the TOUCH and TRANSPOSE buttons to make the tempo faster. ­ 12 ­ 3. DELETING A SONG This function allows you to delete song that were not recorded correctly or song that you do not want to listen to any more. (2) Releasing all the buttons will delete the song NOTE: ­ The total memory capacity of the recorder is approximately 1, 800 notes. When the recorder reaches its maximum capacity, the piano will stop recording at this point. However, memory may be lost if the power remains off for more than 10 days. ­ To delete recorded song (reset), first turn the power off and then turn it back on again while holding down both the PLAY/STOP and REC buttons. ­ 13 ­ PROGRAMMING MODE The Programming Mode gives you access to many other useful features on your piano. To use the Programming Mode functions, press a key on the keyboard while holding down the TOUCH and TRANSPOSE buttons. [. . . ] And, if you press any F key while holding down the TOUCH and TRANSPOSE buttons, the MIDI channel will decrease by 1 each time you press the key. When the power is first turned on, the piano always selects channel 1. ­ 15 ­ 4. TRANSMIT MIDI PROGRAM CHANGE ON/OFF You can use 7 tone buttons to transmit Program Change Numbers via MIDI. Please refer to the list below for assignment of tone and program number. [. . . ]