User manual JWIN JT-P86

[. . . ] - Press and hold the "TIME" key for two seconds and release while voice weekday played. - Press "OGM/FORWARD" or "MEMO/REPEAT" keys to select the right weekday. - After setting minute, the set time will be announced - If no key input within 8 seconds, the set up procedure will be abandoned. 2. 2. 4 Play the current Time Press the "Time' key, the current will be announced. [. . . ] 2. 2. 6 Playing all ICM Messages At beginning of playback LCD will show the total number of messages meanwhile DAM announces the same content by voice. Procedure of playing all messages is as follows: 2. 2. 6. 1 Playback - Press the " PLAY/STOP " key once, the messages will be sequentially played in the order first in first out. (Only if no new message is recorded or all new message(s) is/are played, otherwise only the new message(s) will be played. ) - If date-time stamp (DTS) has been set, the total number of messages DTS is first played. Then each message is played with message number DTS played first and clock DTS played last. 6. 2 Skip message - Press " OGM/FORWARD " key to skip the DTS play or message play, and play the next message. PAGE 3 2. 2. 6. 3 Repeat message - Press " MEMO/REPEAT" key to replay the repeat current message or press twice to replay previous message. 6. 4 Erase single message - Press " ERASE " key to erase the message currently being played back. 6. 5 Stop message play - Press " PLAY/STOP " key to abort the message play. 7 Playing new ICM Messages Procedure of playing new messages is as follows: - If new message(s) has/have been recorded, the ANSWER ON/ OFF LED will keep flashing. - Press the " PLAY/STOP " key, the new messages will be sequentially played - If DTS has been set, the total number of messages DTS is first played. - The ANSWER ON/ OFF LED will stop flashing but will be turned on after all new messages have been played to indicate the absence of new messages. Recording a Memo Memo is a message left for others who directly access to the answering machine. 2. 2. 16 ICM Recording When a call is received in answer-record mode, the machine will play OGM1, and then performs ICM recording. The procedure of ICM recording is as follows: - Answer the call and then play OGM1. - The ICM recording stops if any of the following events occurs, i. e. , 8 seconds of silence/continuous signal/5 seconds busy tone, or record time up to 1 minute, or parallel phone picked up, or " PLAY/STOP " key pressed. If parallel phone picked up is detected, the message being recorded will be saved as a new message. If press " PLAY/STOP " key, the message being recorded will not be saved. - A long beep tone will be transmitted to indicate that ICM recording is finished. - If memory full occurs during ICM recording, pre-recorded OGM2 "Memory full, please call later" will be announced before the machine releases line. 2. 2. 17 Rings Setup - Rings detected to enable line interface will be 5 rings or Toll save 2/5 rings. PAGE 5 - If in "DAM OFF" state, the rings detected is automatically set to 10 or optional 15. - When there is an incoming call ANS/OGM LED will flash in the cadences of the ring. 2. 2. 18 Call Screening When a call is received in DAM ON State, the machine will play OGM. [. . . ] Exit the remote control 2. 2. 19. 3 The remote operation voice prompt: - To play memos press 3. Automatic pause during remote playback of recorded messages: - While in remote control mode, press "4" or "5" to play back recorded messages. - If the caller does not interrupt the playback and the overall duration of playback reaches 180 seconds, the machine will stop playing automatically. - The machine will generate two short beeps and then single-tone beeps to alert the caller. [. . . ]