User manual JVC XU-301

[. . . ] MD-CD COMBINATION DECK PLATINE COMBINÉE MD-CD XU-301BK XU-301 MD-CD COMBINATION DECK 32kHz DIGITAL INPUT 44. 1kHz 48kHz EDIT TITLE DISPLAY /CHARA PLAY MODE CD 3 2 CD CD 1 PLAY & EXCHANGE 3-CD MIXING REC PAUSE REC START REC STOP DIGITAL CD LINE MIC CANCEL SET REC SOURCE SELECTOR STANDBY TIMER CD PITCH CONTROL /CLOCK MIX BALANCE 1st TRACK REC LISTENING EDIT CD REC LEVEL POWER NORMAL SPEED CD REC SKIP MD LINE MIC CD LINE MIN MAX MIC PHONES SAMPLING RATE CONVERTER INSTRUCTIONS MANUEL D'INSTRUCTIONS For Customer Use: Enter below the Model No. Serial No. LVT0009-001B [J] Warnings, Cautions and Others/Mises en garde, précautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN To reduce the risk of electrical shocks, fire, etc. : 1. Do not expose this appliance to rain or moisture. CAUTION "TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL" AC power cord The AC power cord of this unit has certain one-way direction connections to prevent electric shock. Refer to the illustration for correct connection. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] All the REC SOURCE SELECTOR lamps flash when none of the REC SOURCE SELECTOR buttons have been selected. REC 2 Establish the rec pause mode. · · Flashing MIXING DIGITAL CD LINE MIC 3 Select (one of) the recording sources. · · DIGITAL CD : For recording the sound of a unit which has been connected to the OPTICAL IN connector (digital input) : For recording the CDs inserted into CD1, CD2 and/or CD3 (when the CD pitch control is set to OFF for the digital input) Note: Analog recording is performed for CD+LINE or CD+MIC mixing even when the CD pitch control has been set to OFF. : For recording the sound of a unit which has been connected to the LINE IN connector (analog input) : For recording the sound from a microphone which has been connected to the MIC jack (analog input) REC SOURCE SELECTOR · · Press the same button again to clear the selection. LINE MIC · · If a source has already been selected, its corresponding lamp will light. The other lamps go off. 4 When analog signals are supplied, adjust the recording level. Lamp lights. REC LEVEL · Adjust the volume in such a way that the 0 dB display is not exceeded when the loudest sound is supplied. L R 40 30 20 15 10 6 3 0 MIN MAX (The sound will be recorded with some distortion if the OVER display (red) lights continuously. ) 5 Play the sound of the source to be recorded. · If the CD1 button is pressed when CDs serve as the source, the tracks are recorded in the following sequence: CD1 = CD2 = CD3. Press the TRACK MARKING button on the remote control to allocate track numbers during recording. 6 Press the REC START button to start the recording. · REC PAUSE REC START · When MD recording is completed After "UTOC WRITING" is displayed, operation stops automatically. Press the REC STOP button to stop the recording at any time. · DIGITAL INPUT lamps These lamps light as follows in the rec pause or recording mode. · DIGITAL : 32 kHz­48 kHz lights depending on the sampling frequency of the recording source. · CD : 44. 1 kHz lights 28 When DIGITAL IN UNLOCK is scrolled and displayed, the OPTICAL IN connector is not connected to the source unit. In the case of an MD with some remaining space, the end of the last track recorded is automatically searched, and recording is commenced immediately. To record over all the existing tracks, erase all the tracks using the ALL ERASE function (see page 40), and then proceed with the new recordings. Upon completion of the MD recording, "UTOC WRITING" is displayed. Operating any button while this message is displayed may render the MD unusable. Always wait for "UTOC WRITING" to be cleared before proceeding with the next operation. When digital input signals are supplied, they will be recorded in their original digital form. There is no need to adjust their recording level. CD Recording (single-action recording) CD play and MD recording are started simultaneously. 3 XU-301 MD-CD COMBINATION DECK 1 -1 32kHz 2 DIGITAL INPUT 44. 1kHz 48kHz 1 -2 EDIT TITLE DISPLAY /CHARA PLAY MODE CD 3 2 1 PLAY & EXCHANGE CD CD 3-CD MIXING REC PAUSE REC START REC STOP DIGITAL CD LINE MIC CANCEL SET REC SOURCE SELECTOR STANDBY TIMER CD PITCH CONTROL /CLOCK MIX BALANCE 1st TRACK REC LISTENING EDIT CD REC LEVEL POWER NORMAL SPEED CD REC SKIP MD LINE MIC CD LINE MIN MAX MIC PHONES SAMPLING RATE CONVERTER 1 Select and stop the CD to be recorded. Example: When recording CD1 · Only the selected CD is recorded. 2 Insert the recording MD. · CD REC Insert the MD with its label side facing up. Recording starts from track 1. Remaining play time of track being recorded Remaining recording time on MD 3 Press the CD REC button to start the recording. · CD MD DIGITAL L R 40 30 20 15 10 6 3 0 TOC REC "DIGITAL" is displayed. · When a CD is recorded, its digital signals are recorded in their original form. A track mark is automatically placed where one track changes to the next, and the track number also changes. · When MD recording is completed After "UTOC WRITING" is displayed, operation stops automatically. CD play is transferred to the next tray. · To check a track number during recording Main unit DISPLAY /CHARA Remote control Press DISPLAY/CHARA button (or DISPLAY MODE on the remote control). \ Remaining time of track being recorded « CD number and track number MD track number Remaining recording time on MD The mode changes each time this is pressed. 29 English · To stop the recording at any time English Press the 7 (stop) button. The recording mode is released after "UTOC WRITING" is displayed. There is no need to adjust the recording level (for a digital recording). When the CD REC button is pressed, the function is automatically switched to "CD. " This means that when the CD to be recorded has been selected, recording can proceed straightaway. Upon completion of the MD recording, "UTOC WRITING" is displayed. Operating any button while this message is displayed may render the MD unusable. [. . . ] When some of the MD recordings are erased and replaced with new recording repeatedly, empty areas are formed on parts of the disc. When a recording is made on this kind of disc, the data of a track is divided in bits and pieces among and recorded on these empty areas. When the number of these divided areas increases, "DISC FULL" may be displayed during recording. If the data is divided so that some parts are less than 8 seconds in length, it may not be possible to use the JOIN function to join the track concerned. [. . . ]