User manual JVC XM-R700

[. . . ] PORTABLE MINIDISC RECORDER TRAGBARER MINIDISC-RECORDER ENREGISTREUR DE MINIDISC PORTABLE DRAAGBARE MINIDISC-RECORDER XM-R700SL INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING For Customer Use: Enter below the Model No. Serial No. LVT0621-001A [E] WICHTIGER HINWEIS FÜR LASER-PRODUKTE / IMPORTANT POUR LES PRODUITS LASER /BELANGRIJKE INFORMATIE VOOR LASERPRODUKTEN ACHTUNG!DIE VERWENDUNG DER BEDIENUNGS- UND EINSTELLELEMENTE ZU ANDEREN ZWECKEN ALS DEN HIER BESCHRIEBENEN KANN ZUR FREISETZUNG GEFÄHRLICHER LASERSTRAHLUNG FÜHREN. ÖFFNEN SIE KEINE ABDECKUNG UND FÜHREN SIE KEINE REPARATUREN SELBST DURCH. [. . . ] Accidental erasure prevention knob · Remote control operation will be disabled during recording or editing. · Unplugging or plugging of the connection cord or microphone should be avoided during recording. Open Close · Removal of the rechargeable battery should be avoided For recording For protecting during recording. Otherwise, you cannot open the lid unor editing erasure less the rechargeable battery is reinserted or AC adaptor is connected to the unit. 8 English Check Items Before Starting Recording English · The MD is not the Play-only type one. · The accidental erasure prevention knob of the MD cartridge is set to the close position. If not, carry out ALL ERASE or ERASE function mentioned later to erase all the tracks or desired tracks in the MD. You can check the recordable remaining time of the MD by repeatedly pressing the DISPLAY/CHARA. (See "Showing the Disc Information" on page 7. ) Standard Recording CAUTIONS: · Be sure that the rechargeable battery is fully charged. · While "UTOC Writing" appears on the display, to avoid improper recording, do not give a shock to the Unit and do not disconnect any cable from the Unit, including the AC adaptor's cable. Notes · The recording operation is possible only with the buttons on the unit. · When a stereo signal is recorded in MONO mode, stereo sound will be heard though the signal is correctly recorded in MONO mode. 1 2 3 Check the things before recording. See "Check Items Before Starting Recording" above. Insert an MD with its label side facing up. Proceed to the next step after "TOC Reading" goes out on the display. Slide the REC switch. The unit enters Rec/Standby mode, the REC indicator lights up, and the disc mark blinks. The track number is increased by one. (Appears only if MONO is selected. ) Total track number Remaining time Recording mode · To cancel Rec/Standby mode, press the 7/CHARGE button. 4 Within two minutes, press the REC MODE button to select the recording mode. Each time you press the button, the display changes as follows: SP = LP2 = LP4 = MONO SP: Signifies standard-hour stereo recording. The number of hours usable for recording is the same shown on the package of the MD. The number of hours usable for recording is twice long as shown on the package of the MD. The number of hours usable for recording is 4 times long as shown on the package of the MD. The number of hours usable for recording is twice long as shown on the package of the MD. as as as as 5 6 7 Play the recording source. Adjust the recording level for analog input only. See "Adjusting the recording level" on page 10. Press the 6 button to start recording. When the MD becomes full, "UTOC Writing" appears on the display, indicating that the recording is successfully completed. (The "TOC" indicator goes out. ) To pause, press the 6 button. (The track number is increased by one. ) To cancel pause, press the 6 button again. "UTOC Writing" appears on the display and then the MD stops. (The "TOC" indicator goes out. ) Notes · During recording, recording mode does not change even if the REC MODE button is pressed. · Once you have set the recording mode, it remains until the Unit is turned off. When the Unit is turned on, SP (Stereo) recording mode is always selected. 9 Title "LP:" ON/OFF To increase the space usable for a title, you can delete the recording mode name "LP:" that will be added immediately before the title. [. . . ] The amount of recorded time on the disc added to Minidiscs must have at least 2 seconds (SP mode) of continuous the amount of remaining time falls shout of the space in order to record. For this reason, the actual recording time of discs with a lot of short blank areas becomes shorter. disc's total possible recording time. Rules of Digital Dubbing The following rules regarding copyright exist for dubbing to MDs from CDs or DATs through digital terminals. SCMS (Serial Copy Management System) Minidiscs can record clear sound with low loss of quality from CDs or DATs through each component's digital input/output terminal. However, minidiscs are set up so that a disc recorded in this way cannot be recorded onto another minidisc through digital input/output terminals. [. . . ]