User manual JVC UX-T550

[. . . ] Serial No. GNT0001-001A [B] NEDERLANDS ESPAÑOL DEUTSCH MICRO COMPONENT SYSTEM ENGLISH Caution ­ switch! REPRODUCTION OF LABELS AND THEIR LOCATION Disconnect the mains plug to shut the power off completely. CAUTION To reduce the risk of electrical shocks, fire, etc. : 1. Do not remove screws, covers or cabinet. WARNING The unit contains a built-in lithium battery for memory back-up that must only be replaced by suitably qualified service personnel. For battery replacement, take the unit to your dealer or a JVC service station. IMPORTANT FOR LASER PRODUCTS PRECAUTIONS 1. [. . . ] To designate track number 11 or higher, press the +10 button the required number of times, then a track number button. (Example: To designate the 20th track, press the +10 button once, then press track number button 10. ) * +10 button: Each time this button is pressed, the number increases by 10. First press this button to set the 10's digit, then press the track number button to set the 1's digit. To skip to another track during play When the required track number button is pressed, the display shows the designated track number and play starts from the beginning of the designated track. 8 Programmed play (using the remote control unit) Up to 20 tracks can be programmed to be played in any required order. The total playing time of programmed tracks is displayed (up to 99 minutes, 59 seconds). (Example: When programming the 2nd track to be played first, and the 6th track next, then the 12th track, etc. ) ~ CD Y ! / 2 PROGRAM To designate the 2nd track. 2 PROGRAM PROGRAM @ 6 To designate the 12th track. ¤ CD +10 2 2 6 2 6 12 PROGRAM PROGRAM The 12th track The total playback time of programmed tracks is displayed. ~ Press the CD 3/8 button to set to the CD mode. Press the PROGRAM button; the tracks making up the program will be displayed in programmed order. Track number / Press to designate the required track number. @ Designate the remaining tracks by pressing the track number buttons. When the CD holder is opened, programmed tracks are cleared automatically. Notes: If the total playing time of the programmed tracks exceeds 99 minutes 59 seconds, the total playing time indication will go out. When programming a track number higher than 21 on a disc containing more than 21 tracks, the total playback time of all the programmed tracks will not be displayed. When a disc with 16 or more tracks is loaded, the "OVER" indicator will appear. PROGRAM 2 PROGRAM Program order number Repeat play (using the remote control unit) Press the REPEAT button before or during play. Whether a single track or all tracks are to be repeated can be specified. Each time the REPEAT button is pressed, the mode will change from a single track ( ), to all the tracks ( ALL), to the clear mode, in this order. Single track repeat ( ) The current or specified track will be played repeatedly. All tracks repeat ( ALL) All tracks or the programmed tracks of a CD will be played repeatedly. Random play (using the remote control unit) Press the RANDOM button, and all tracks on a CD play once in random order. REPEAT ALL Single track All tracks RANDOM Goes off. Repeat playback is released. 9 HANDLING CASSETTE TAPES Cassette tapes 1. To prevent recordings from being erased accidentally, remove the tab(s) with a screwdriver, etc. Reseal the slots with adhesive tape to erase and re-record after the tabs have been removed. C-120 cassettes are not recommended because they are prone to malfunction. Turn the pencil to tighten the tape. Listen for the click indicating that the holder is securely shut. Tab "B" Side "B" Tab "A" Adhesive tape Note: If the power is switched off while tape is running, it may be impossible to remove the cassette. If this happens, switch the power on again before attempting to remove the cassette. [. . . ] Checking the sleep time When the SLEEP button is pressed, the remaining sleep time is displayed. To cancel the sleep timer operation Press the button to switch the power off or press the SLEEP button until the sleep time indicator disappears. Any source can be selected for sleep timer operation and timer playback. For example; · CD play for sleep timer operation and broadcast reception for timer playback. · Tape playback for sleep timer operation and CD play for timer playback. [. . . ]