User manual JVC UX-H10

[. . . ] MICRO COMPONENT SYSTEM UX-H10 --Consists of CA-UXH10 and SP-UXH10 TIMER SET TIMER ON/OFF STANDBY/ON INTRO /RDS SEARCH RANDOM SLEEP STANDBY/ON REMAIN /RDS MODE PROGRAM REPEAT ST/MONO VOLUME TAPE TUNER /BAND CD CD BEAT CUT STANDBY MICRO COMPONENT SYSTEM UX-H10 DISPLAY /CLOCK SET MUTING SOUND /BASS VOLUME RM-SUXH10R REMOTE CONTROL CD SYNCHRO RECORDING OPEN INSTRUCTIONS LVT1092-005B [B] Warnings, Cautions and Others IMPORTANT for the U. K. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. [. . . ] The clock may gain or lose 1 to 2 minutes per month If this happens, reset the clock. 8 Adjusting the Volume You can adjust the volume level only while the unit is turned on. The volume level can be adjusted between "VOL MIN, " "VOL 1" "VOL 39, " and "VOL MAX. " The volume level has no effect on recording. When you press and hold either button, you can change the volume level continuously. Selecting the Sound Modes You can select one of the 4 sound modes. This function only affects the playback sound, and does not affect your recording. Each time you press the button, the sound mode changes as follows: POP CLASSIC JAZZ ROCK SOUND /BASS VOLUME FLAT (Canceled) To turn off the sound temporarily On the remote control ONLY: Press MUTING. The volume level turn down and "MUTING" starts flashing on the display. MUTING POP: More presence in the vocals and midrange. FLAT: Equalizer effect is canceled. To restore the sound, press MUTING again. Adjusting the volume level also cancels the muting. When the sound mode is activated, the SOUND indicator lights up on the display. For private listening Connect a pair of headphones to the PHONES jack. Be sure to turn down the volume before connecting or putting on the headphones. Reinforcing the Bass Sound The richness and fullness of the bass sound is clearly maintained regardless of how low you set the volume--Hyper Bass Sound. This function only affects the playback sound, and does not affect your recording. To get the effect, press and hold SOUND/BASS until "HBS ON" appears and the BASS indicator lights up on the display. SOUND /BASS DO NOT turn off (standby) the unit with the volume set to an extremely high level; Otherwise, the sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the unit or start playing any source. REMEMBER you cannot adjust the volume level while the unit is in standby mode. Each time you press and hold the button, the effect alternates on ("HBS ON") and off ("HBS OFF"). To cancel the effect, press and hold SOUND/BASS again until "HBS OFF" appears and the BASS indicator goes off. 9 Listening to FM and AM (MW) Broadcasts Tuning in to a Station To change the FM reception mode On the remote control ONLY: 1 Press TUNER/BAND to select either "FM" or "AM. " TUNER /BAND The unit automatically turns on and tunes in to the previously received station--either FM or AM (MW). Each time you press the button, the band alternates between FM and AM (MW). When an FM stereo broadcast is hard to receive or noisy, press REPEAT ST/MONO so that the MONO indicator lights up on the display. Reception will improve. REPEAT ST/MONO To restore the stereo effect, press REPEAT ST/MONO again so that the MONO indicator goes off. In stereo mode, you can hear stereo sound when a stereo program is broadcast. To reduce the beat--Beat Cut 2 Press and hold or 4 (/): Increases the frequencies. 4 (4/1): Decreases the frequencies. On the remote control ONLY: If the beats are heard while listening a broadcast, press BEAT CUT. BEAT CUT (or / or 4/1 on the unit) for more than 1 second. The unit starts searching for stations and stops when a station of sufficient signal strength is tuned in. If an FM program is broadcast in stereo, the ST (stereo) indicator lights up on the display (only when the reception is good). To stop during searching, press or 4 (or / or 4/1 on the unit). When you repeatedly press or 4 (or / or 4/1 on the unit) The frequency changes step by step. 10 Presetting Stations You can preset 20 FM and 20 AM (MW) stations manually. In some cases, test frequencies have been already stored for the tuner since the factory examined the tuner preset function before shipment. You can preset the stations you want into memory by following the presetting method. If the setting is canceled before you finish, start again from step 2. Tuning in to a Preset Station On the remote control ONLY: 1 Press TUNER/BAND to select either "FM" or "AM. " TUNER /BAND The unit automatically turns on and tunes in to the previously received station--either FM or AM (MW). Each time you press the button, the band alternates between FM and AM (MW). On the remote control ONLY: 2 Press number. or to select a preset 1 Tune in to the station you want to preset. See "Tuning in to a Station" on page 10. 2 Press PROGRAM. The PROG (program) indicator and "00" start flashing on the display. PROGRAM 3 Press number. or to select a preset 4 Press PROGRAM again. The PROG indicator and the selected preset number stop flashing. PROGRAM 5 To preset more stations, repeat steps 1 to 4 above, allocating a different preset number to each station. Storing a new station on an already assigned number erases the previously stored one. When you unplug the AC power cord or if a power failure occurs The preset stations will remain in the unit. 11 Receiving FM Stations with RDS RDS (Radio Data System) allows FM stations to send an additional signal along with their regular program signals. [. . . ] Turning off the unit also cancels the Sleep Timer. If the unit is already turned on when the timer on-time comes The timer does not works. When you unplug the AC power cord or if a power failure occurs The timer will be canceled. You need to set the clock first, then set the timer again. When you set the Sleep Timer after the Daily Timer starts playing the selected source The unit turns off with either timer having an earlier shut-off time. If you set the Sleep Timer while playing back or recording a tape Do not shut the unit off with the Sleep Timer while a tape is running. If the unit turns off while playing back or recording a tape, the cassette deck or tapes may be damaged. 20 Maintenance To get the best performance of the unit, keep your discs, tapes and mechanism clean. General Notes In general, you will have the best performance by keeping your discs, tapes and the mechanism clean. Store discs and tapes in their cases, and keep them in cabinets or on shelves. Handling cassette tapes If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels and rotating. [. . . ]