User manual JVC UX-5000

[. . . ] ULTRA MICRO COMPONENT SYSTEM ULTRA-MIKRO-KOMPONENTEN-SYSTEM SYSTEME DE COMPOSANTS ULTRA MICRO ULTRA MIKRO KOMPONENTENSYSTEEM SISTEMAS DE COMPONENTES ULTRA MICRO SISTEMA AD ULTRA MICROCOMPONENTI UX-5000 AHB. SUPER PRO PRESET TUNING DOWN MULTI CONTROL UP CLOCK SLEEP REMOTE CONTROL RM-RXU5000 OPEN/CLOSE AUX MD/TAPE TUNER BAND CD DIMMER SLEEP TIMER/SNOOZE DISPLAY FM MODE AHB. AUTO SUPER PRO PRESET AUX CD PROGRAM RANDOM REPEAT BASS TREBLE CANCEL UP SET DOWN VOLUME STANDBY MD /TAPE TUNER BAND CD VOLUME ULTRA MICRO COMPONENT SYSTEM UX-5000 PHONES INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES ISTRUZIONI For Customer Use: Enter below the Model No. Serial No. LVT0034-001A [E] Warnings, Cautions and Others / Warnung, Achtung und sonstige Hinweise /Mises en garde, précautions et indications diverses /Waarschuwingen, voorzorgen en andere mededelingen/Avisos, precauciones y otras notas / Avvertenze e precauzioni da osservare Caution ­­ switch! [. . . ] s Before listening to the radio: · Check that both the FM and AM (MW/LW) antennas are correctly connected. Press the UP or DOWN button on the Remote Control to select the desired preset number. After 1 second the display will show the preset number's band and frequency. Example:Press the UP button until the preset number 12 "P-12" appears. UP One Touch Radio ------------------ s or DOWN Just press the TUNER BAND button to turn on the System and start playing the station you were last tuned to. s You can switch from any other sound source to the radio by pressing the TUNER BAND button. (After 1 second) Preset Tuning using the Unit (Possible only after presetting stations) Press the PRESET TUNING button to select the desired preset number. s Press the TUNER BAND button. The Band and Frequency you were last tuned to appear on the display. (If the last station was selected using the preset number, the preset number appears first. ) Each time you press the button, the band alternates between FM and AM (MW/LW). AM TUNER BAND Presetting Stations You can preset up to 30 FM stations and up to 15 AM (MW/LW) stations using the Remote Control. Note: Preset numbers may have been set to factory test frequencies prior to shipment. You can preset the stations you want into memory by following one of the presetting methods below. FM Manual Presetting TUNER BAND SET ------------------ UP 2. s Select a station using one of the following methods. or DOWN SET s s s Manual Tuning Press the 4 or ¢ button on the Unit or the Remote Control repeatedly to move from frequency to frequency until you find the station you want. OR Auto Tuning If you press and hold the 4 or ¢ button on the Unit or the Remote Control for one second or more, the frequency changes down, or up, automatically until a station is found. OR Preset Tuning using the Remote Control (Possible only after presetting stations) When changing the Band FM = 30, AM = 15 1. The lower 2 digits blink. 8 select the preset number. UP button: Increases the preset number by 1. s Press the SET button. After 1 second, the display returns to the broadcast frequency display. 6. s Repeat above steps 1 to 5 for each station you want to store in memory with a preset number. To cancel during presetting, press the CANCEL button in step 3 or 4. To change the preset stations, repeat the same steps as above. Auto Presetting In each band, you can automatically preset FM-30, AM (MW/LW)15 stations. Preset numbers will be allocated as stations are found, starting from the lowest frequency and moving up the frequency. TUNER BAND AUTO PRESET (for 2 seconds) 1. s Repeat steps 1-2 for the other band. Remote Control for more than two seconds. s If you want to change the preset stations, carry out the Manual Presetting for the desired preset numbers. CAUTION: If the System is unplugged or if a power failure occurs, the preset stations will be erased after about 24 hours. If this happens, you will need to preset the stations again. To Change the FM Reception Mode When you are tuned into an FM stereo broadcast, the "ST (Stereo)" indicator lights up and you can hear stereo effects. If an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Press the FM MODE button on the Remote Control so that the "MONO" indicator lights up on the display. FM MODE ST(Stereo) MONO To restore the stereo effect, press the FM MODE button on the Remote Control so that the "MONO" indicator goes off. 9 English 4. s Press the UP, DOWN, >, or < button to English s Using the CD Player s REMOTE CONTROL RM-RXU5000 DIMMER SLEEP DISPLAY FM MODE AHB. [. . . ] Then, press the TIMER/ SNOOZE button repeatedly, and you can see the current timer settings (ON time, OFF time, source, and volume). To change the timer setting, repeat the setting procedure from the beginning. · · When the timer turns on, the Timer indicator starts blinking. When the timer turns on, it is possible to fade in the sound from volume level 0 (zero) to the preset volume. CAUTION: If the System is unplugged, or a power failure occurs, the timer setting will be lost after about 24 hours. [. . . ]