User manual JVC TM-H1750CG-U-TM-H1750 Instruction Manual

[. . . ] TM-H1750CG OPERATING INSTRUCTIONS [ TM-H1750CG/E / TM-H1750CG/U ] COLOR VIDEO MONITOR ENGLISH ASPECT A B C SLOT D BEDIENUNGSANLEITUNG : FARB-VIDEO-MONITOR MANUEL D'INSTRUCTIONS : MONITEUR VIDEO COULEUR MANUALE DI ISTRUZIONI : MONITOR VIDEO A COLORI INSTRUCCIONES : MONITOR DE VIDEO A COLOR !"#$%&'(&) Pour l'usage du client: Enter ci-dessous le numéro de série qui est situé sur l'arrière du coffret. Conserver cette information pour une référence ultérieure. : Numéro de série : TM-H1750CG CHROMA CONTRAST VOLUME/SELECT MENU UNDER SCAN COLOR OFF BLUE CHECK POWER TM-H1750CG PHASE BRIGHT INPUT SELECT LCT1025-001A-H 1101-Y-U-JMT Jan. 51923 ESPAÑOL ITALIANO For Customer Use: Enter below the Serial No. [. . . ] * The on-screen display goes off when you press MENU button. Phase control is effective only in the NTSC color system mode. Chroma control is not effective when receiving RGB and B/W or when no signal is input. (Except when a component signal is input. ) When CHROMA is adjusted to "­40, " the picture becomes less colorful. "NO EFFECT" is displayed (for about 3 seconds) when your selected function has no effect. To change the display position on screen, set UPPER or LOWER with ADJ. BAR POSI. ENGLISH INPUT SELECT buttons 1 Input A (VIDEO) 2 Input B (VIDEO/Y/C) Terminals on the rear panel Video signal input VIDEO A terminal VIDEO B terminal Audio signal input AUDIO A terminal AUDIO B terminal No. 51923 8 TM-H1750CG 9 1-5 APERTURE ADJ. LEVEL* RUSH DELAY Input the standard color-bar signal for your TV system and display it on the screen. When the BLUE CHECK button is pressed, the red and green signals are cut and only the blue signal is displayed. The BLUE CHECK function adjusts and checks CHROMA (COLOR) GAIN and PHASE. LEVEL has been initialized when a component signal is input. CONTRAST/ BRIGHT Reverse selection mark (4) select. 4 Function display: The functions of the front panel buttons (5 buttons on the left) correspond to the function displayed. Input the standard color-bar signal for your TV system and display it on the screen. Press the CHROMA button to adjust the chroma so that the blue bars on the left and right sides of the screen have the same brightness. (Only when an NTSC signal is input) Press the PHASE button to adjust the phase so that the two blue bars at the center of the screen have the same brightness. (Only when an NTSC signal is input) Repeat procedures 3 and 4 for the adjustment so that all four blue bars on the screen have the same brightness. When you have finished making the adjustment, press the BLUE CHECK button to deactivate. 3. Press the VOLUME/SELECT buttons to set. Blue Blue VOLUME/SELECT Contents Forward the menu item. Reverse the menu item. Blue Blue Front panel button VOLUME/ SELECT (+) VOLUME/ SELECT (­) Function displayed + Contents Increase (to max. value) Reverse the setting value Setting range 00 +01 ············ +39 +40 4 ­ ­ + Lower the adjustment value. Exits the <MENU> screen. UPPER 1 Menu items APERTURE ADJ. BAR POSI COLOR TEMP. LEVEL* RUSH DELAY Purpose Picture aperture level Volume bar position Color temperature of white balance Color system Component level Delay time LOWER 6500 AUTO 4 1 EXIT Initializing COMPO. LEVEL (when a component signal is input) with the IF-C01COMG component/RGB input card inserted When a component signal is input, be sure to adjust (initialize) the COLOR offset in COMPO. [. . . ] (See page 9. ) Press the COLOR OFF button and BLUE CHECK button to adjust. (See page 10. ) Move the device away from the monitor and turn the monitor's power off. Switch the aspect ratio to 4:3 with the ASPECT button on the front panel. No. 51923 18 Unnatural, irregularly colored, or distorted picture. Dark stripes appear at the top and bottom of the screen, picture vertically squeezed. [. . . ]