User manual JVC TH-A5 Instruction Manual

[. . . ] DVD DIGITAL CINEMA SYSTEM TH-A5R Consists of XV-THA5R and SP-THA5R STANDBY/ON AUDIO VCR CONTROL OFF ON TV VCR TOP MENU MENU TV CHANNEL AUDIO/ FM MODE SUBTITLE TV VOLUME DISPLAY RETURN STEP TV/VIDEO TUNER PRESET DOWN REW VCR CHANNEL TUNING B. SEARCH F. SEARCH UP FF ENTER VOLUME DVD FM/AM AUX MUTING COMPACT DIGITAL VIDEO STANDBY AUDIO/FM MODE STANDBY/ON DSP VOLUME SOURCE DVD DIGITAL CINEMA SYSTEM TH-A5R RM-STHA5R DVD CINEMA SYSTEM DIGITAL SURROUND DIGITAL INSTRUCTIONS For Customer Use: Enter below the Model No. Serial No. LVT0837-004A [B] Warnings, Cautions and Others IMPORTANT for the U. K. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] To adjust the overall level of DSP effect, go to step 5 on the next page. 3 2) Press 3 or 2 to adjust the output level. 3 : Increases the output level. 2 : Decreases the output level. ENTER To adjust the output balance for the front speakers and the rear speakers 1) Press SOUND repeatedly until one of the following adjustment indications appears on the display. SOUND Each time you press the button, the indication on the display changes as follows: 3) Repeat 1) and 2) for setting the other speakers. 00 F 00 Normal indication (canceled) 00 R 00 REVERB LIVE REAR ROOM Adjusting DSP Modes You can adjust the following settings while activating DSP modes. It is recommended that you make adjustments from your actual listening point while listening to reproduced sounds. Output balance for the front speakers Output balance for the rear speakers Output level for the rear speakers Output level for the subwoofer Overall level of DSP effect DSP modes cannot be used with Dolby Surround. Once one of DSP modes is activated, Dolby Surround in use will be canceled. When you play back a DVD encoded with Dolby Digital or DTS Digital Surround, DSP MODE button (or DSP button on the center unit) does not work. Make sure that you have set the speaker information correctly (see page 16). You cannot adjust the speaker output balance and levels when you have set the speaker settings to "NONE. " There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again. 00 F (Front) 00 : To adjust the output balance for the front speakers. "00 F 00" and "00 R 00" are the initial setting (the output balances are at the center position). If you have already changed the setting, another value will appear. 2) Press 3 or 2 to adjust the output balance. 3 : Decreases the left speaker ENTER output, or restores the right speaker output. 2 : Decreases the right speaker output, or restores the left speaker output. Each output balance changes from OFF (silence), 06 (most reduction) to 00 (no reduction). 3) Repeat 1) and 2) for setting the other speaker. TO BE CONTINUED ON THE NEXT PAGE 23 Creating Realistic Sound Fields Adjusting DSP Sound Parameters REW VCR CHANNEL TUNING B. SEARCH F. SEARCH FF You can fine-adjust DSP modes more minutely by changing three parameters--room, liveness, and reverberation. If the setting is canceled before you finish, start from step 2 again. 23 ENTER VOLUME DVD FM/AM AUX MUTING 1 SOUND RDS DISPLAY TA SOUND Press DSP MODE (or DSP on the front panel) repeatedly to select the desired DSP mode. Press SOUND repeatedly to select the desired DSP sound parameter. Each time you press the button, the indication on the display changes as follows: DSP MODE 1 PTY 2 PTY SEARCH 3 PTY + SETTING 4 7 SLOW 5 8 0 6 PRO LOGIC 2 DSP MODE EFFECT SOUND 9 SETUP TEST ANGLE ZOOM D. R. C DSP MODE REPEAT A-B REPEAT PROGRAM EFFECT 00 F 00 Normal indication (canceled) 00 R 00 REVERB LIVE REAR ROOM CLEAR SEARCH REMAIN SLEEP 4 To adjust the output level for the rear speakers 1) Press SOUND repeatedly until "REAR" SOUND appears on the display. Each time you press the button, the indication on the display changes as follows: ROOM : To adjust the resonance based on the room size. The larger this value is, the more effective the resonance is (from 04 to 16 by 2 steps). The larger this value is, the more liveness is obtained (from 04 to 16 by 2 steps). REVERB (Reverberation) : To adjust the reverberation time of the sound (from 0. 0 msec to 1. 6 msec by 0. 2 msec steps). The following diagram shows the "DEFAULT (initial)" settings of the DSP sound parameters for each DSP mode. DSP MODE HALL THEATER PAVILION DANCE CLUB LIVE CLUB ROOM 08 04 08 04 08 LIVE 16 10 04 08 16 REVERB 0. 4 1. 0 0. 2 1. 6 1. 4 00 F 00 Normal indication (canceled) 00 R 00 REVERB LIVE REAR ROOM REAR : To adjust the output level for rear speakers (from 06 dB to +06 dB). If you have already changed the setting, another value will appear. 2) Press 3 or 2 to adjust the output level. 3 : Increases the output level. 2 : Decreases the output level. 5 To adjust the overall level of DSP effect EFFECT Press EFFECT repeatedly to adjust the overall level. [. . . ] If there are more than one code listed for your brand of TV, try each one until the correct one is entered. Manufacturers' codes for TV Manufacturer Codes 01 12 12 09, 17, 21 11, 13, 14, 24 02, 16 23 13, 14, 24 08, 23 27 02, 20, 22 13, 14, 22 24 03 06, 32 12, 16 12 10, 31 15, 16 14, 24, 28 13, 14, 24, 33, 34 07, 16 19, 21 TV VOLUME DISPLAY RETURN STEP TV/VIDEO TUNER PRESET DOWN REW VCR CHANNEL TUNING B. SEARCH F. SEARCH UP FF ENTER VOLUME DVD FM/AM AUX MUTING Number buttons RDS DISPLAY TA SOUND 1 PTY 2 PTY SEARCH 3 PTY + SETTING 4 7 SLOW 5 8 0 6 PRO LOGIC 9 SETUP TEST ANGLE ZOOM D. R. C DSP MODE REPEAT A-B REPEAT PROGRAM EFFECT CLEAR SEARCH REMAIN SLEEP JVC Akai Fisher Grundig Hitachi Mitsubishi Nokia Nordmende Panasonic Philips Saba Samsung Sanyo Schneider Sharp Sony Telefunken Thomson Toshiba Manufacturers' codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment. 55 Maintenance To get the best performance of the unit, keep your discs and mechanism clean. General Notes In general, you will have the best performance by keeping your discs, and the mechanism clean. Keep the disc tray closed when not in use. Cleaning the unit Stains on the unit Should be wiped off with a soft cloth. [. . . ]