User manual JVC TD-W254

[. . . ] TD-W254B/J DOUBLE CASSETTE DECK DOUBLE CASSETTE DECK TD-W254 B/J Area suffix B . . . . . . . . . . . . . . . . . . . . U. S. A. TD-W254 DOUBLE CASSETTE DECK DOLBY B-C NR HX PRO STANDBY TD-W254 DOUBLE CASSETTE DECK DOLBY B-C NR HX PRO STANDBY COUNTER RESET INPUT LEVEL 5 4 6 3 7 COUNTER RESET COUNTER RESET INPUT LEVEL 5 4 6 3 7 COUNTER RESET A PLAYBACK AUTO REVERSE 3MOTOR SILENT MECHANISM AUTO REVERSE 2 1 PLAY 8 9 MIN MAX REC/REC MUTE PAUSE 3MOTOR SILENT MECHANISM REC/PLAYBACK B A PLAYBACK AUTO REVERSE 3MOTOR SILENT MECHANISM AUTO REVERSE 2 1 PLAY 8 9 MIN MAX REC/REC MUTE PAUSE 3MOTOR SILENT MECHANISM REC/PLAYBACK B COMPULINK Component PLAY COMPULINK Component PLAY POWER PHONES DOLBY B NR REVERSE MODE B OFF C A B SYNCHRO DUBBING NORM SPEED HIGH SPEED POWER PHONES DOLBY B NR REVERSE MODE B OFF C A B SYNCHRO DUBBING NORM SPEED HIGH SPEED AUTO TAPE SELECTOR / CONTINUOUS PLAY ON OFF AUTO TAPE SELECTOR / CONTINUOUS PLAY STANDBY / ON (B version) (J version) INSTRUCTIONS For Customer Use: Enter below the Model No. Serial No. VNN2358-672M id8/i10371/ 11/22/96 Page 2 IMPORTANT (In the United Kingdom) Mains Supply (AC 230 V z, 50 Hz only) RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION ``TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. '' DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. [. . . ] , : Indicates the direction of tape travel. 9 0 q w e r 6 Dubbing mode indicators ``DUBBING >'' : Lights when in the normal-speed dubbing mode. ``DUBBING >>'' : Lights when in the high-speed dubbing mode. 8 Mechanism mode indicators (Deck B) PLAY : Lights when the unit is in the playback and record modes. REC : Lights when the unit is in the record and record-pause modes; blinks during record muting. : Pause indicator : This lights when winding the tape from left to right. COUNTER RESET button (deck B) (eject) button (deck B) Cassette holder (deck B) DOLBY NR switch Set to B or C for recording using the Dolby NR system or for playing back a tape that was recorded using the Dolby NR system. REVERSE MODE switch Select the single side or full record/playback mode, or the continuous play mode. PHONES jack Connects headphones (with an impedance of 8 to 1 k). ­6­ id8/i10371/ 09/23/99 Page 7 8 PLAYBACK 1 POWER POWER ON OFF STANDBY / ON (B version) 2 t INPUT LEVEL control y Cassette operation buttons (deck B) : Press to wind the tape quickly from right to left. REC/ : Press the PLAY button while pressing REC MUTE this button to start recording, and press to leave an appropriate non-recorded section. (See page 9. ) PAUSE : Press to stop the tape temporarily during recording and playback. · HIGH SPEED : Press to perform high-speed dubbing. A (J version) 3 4 DOLBY B NR B OFF C 5 REVERSE MODE 6 PLAY AUTO REVERSE OPERATION The auto reverse operation of this unit turns the tape transport over to the reverse of forward direction automatically when the tape reaches its end during recording or playback. · Because of cassette shell construction, a tape recorded in the forward direction should be played back in the same direction to obtain stable sound reproduction. · During recording, auto reverse can be activated only from the forward to the reverse direction. For good sound quality and to avoid accidental erasure of previously recorded material, always start recording with the side A of the tape facing out. Playback of deck A Operate in the order of the numbers in the illustration. Reverse direction ( PLAY) 4 Set the DOLBY NR switch to the same setting as when the tape was recorded. · When the deck contains a tape, it can be played back by just pressing the PLAY button in the B version only when the POWER switch is set to ON and the switch is at STANDBY. In the J version, the tape can be played back by pressing the PLAY button only when the POWER switch is set to STANDBY. Playback of deck B Perform steps 2 to 6 of the above procedure for deck B. Load cassette tapes in both decks and press the PLAY button of the deck to be played first for continuous play of both decks. · At this time, the CONT indicator lights in the multimode display. When the tape in the deck which plays first reaches the end of side B (in the reverse direction), it automatically switches to the forward direction and enters the standby mode. · While one deck is playing back, the cassette in the other one can be replaced. [. . . ] 2 Load a prerecorded tape with side A facing out into deck A, and press the (direction) button to select the travel direction. 3 Load the blank tape with side A facing out into deck B, and press the (direction) button to select the side to be recorded. (Deck B) 6 Press the SYNCHRO DUBBING (NORM or HIGH SPEED) button to start dubbing. · Synchro record muting When deck A stops or enters any mode other than the playback mode during dubbing, deck B enters the record mute operation automatically and then enters the record-pause mode. [. . . ]