User manual JVC TD-W118

[. . . ] BE SURE to replace the fuse only with an identical approved type, as originally fitted and to replace the fuse cover. If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. DO NOT make any connection to the terminal which is marked with the letter E or by the safety earth symbol or coloured green or green-and-yellow. The wires in the mains lead on this product are coloured in accordance with the following code: Blue to N (Neutral) or Black Brown to L (Live) or Red As these colours may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated ``dangerous voltage'' within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. [. . . ] 3 ­4­ id8/i10371/ 09/23/99 Page 5 CONNECTIONS · · · · Do not switch the power on until all the connections are completed. When the pin-plug cords are employed, always connect the white plug to the left channel terminal. When using the Compu Link Control System version 3, do not connect the power cord to the SWITCHED AC OUTLET of an amplifier or receiver. Otherwise, the automatic power on/ STANDBY function cannot be carried out. 2. Remote cable connection for COMPU LINK · By connecting a remote cable, COMPU LINK functions (automatic power on/STANDBY, automatic source selection, synchronized recording and DDRP recording) can be performed. · When making synchronized recording with a CD player, connect the remote cable to the COMPU LINK-3/SYNCHRO jacks. When making synchronized recordings, only a single deck should be connected to the amplifier. If a component is not a JVC COMPU LINK component, bypass it when making the remote cable connections. This deck can be connected with an amplifier and a CD player which have the COMPU LINK-1/SYNCHRO jacks for COMPU LINK performance. Connection to a stereo amplifier Note: When installing the deck, be sure to install at a distance from your amplifier. If they are stacked, noise (hum) may occur. Stereo amplifier Deck Remote cable (provided) Remote cable (provided with CD player) CD player CASSETTE LOADING 1. · At this time, the CONT indicator lights in the multimode display. When the tape in the deck which plays first reaches the end of side B (in the reverse direction), it automatically switches to the forward direction and enters the standby mode. · While one deck is playing back, the cassette in the other one can be replaced. Note: · Use tapes recorded using the same NR mode in decks A and B. ­7­ id8/i10371/ 09/23/99 Page 8 RECORDING Deck B only Operate in the order of the numbers in the illustration. · Make sure the safety tab of the cassette has not been broken off. 1 POWER It should be noted that it may be unlawful to re-record prerecorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein. POWER ON OFF STANDBY / ON DDRP (Dynamics Detection Recording Processor) recording (J version) DDRP recording is performed with suitable JVC CD players and the recording level adjustment is performed automatically. Since recording level adjustment is performed automatically for different types of tape (normal, CrO2 and metal), the adjustment of INPUT LEVEL control is not required. Read the instruction book of your CD player carefully. (B version) 2 A RECORDING LEVEL ADJUSTMENT 3 DOLBY B NR B OFF C 4 REVERSE MODE Adjust the recording level while observing the peak level indica tor indication. For example: With metal tape 5 6 REC/REC MUTE PAUSE Because of metal tape's higher saturation level, it is OK that ``+ 2'' lights occasionally. 7 INPUT LEVEL 5 4 6 3 2 1 MIN 7 8 9 MAX 8 9 With normal or chrome tape COUNTER RESET PLAY It is OK that ``+ 0'' lights occasionally. · 1 2 3 4 5 6 Turn the power on. Notes: · When the safety tabs are removed from a cassette tape, the tape cannot be recorded even if you try. [. . . ] · The source is locked to the CD position during synchronized recording or DDRP recording to avoid accidental stops or switch-over to another component. To switch over the components, cancel synchronized recording or DDRP recording first. · The INPUT LEVEL control does not function during DDRP recording. DUBBING · Synchro dubbing Operate in the order of the numbers in the illustration. 1 POWER POWER ON OFF STANDBY / ON (B version) 2 A (J version) 3 A 4 REVERSE MODE 5 COUNTER RESET 6 A B SYNCHRO DUBBING NORM SPEED HIGH SPEED 7 1 Turn the power on. [. . . ]