User manual JVC SR-V10U

[. . . ] VIDEO CASSETTE RECORDER SR-V10U TV CABLE/ DBS MBR SET A/B POWER TV/VCR A. MONITOR DISPLAY 1 4 DBS 2 5 DAILY 3 2 6 WEEKLY 7 C. RESET 8 AUX 9 TIMER 4 CANCEL 0 STOP DATE START CH EXPRESS PROGRAMMING 1 PROG PROG CHECK SP/EP SKIP SEARCH PLAY REW FF REW PLAY FF REC STOP PAUSE POWER ­ + MENU 3 OK TV CH + CH­ /+ PUSH / TURN SHUTTLE PLUS L ­ O V L TV VO + TV REC LINK S VIDEO VIDEO (MONO)L--AUDIO--R SP EP VCR A. DUB 24HR QUICK PROGRAM TV CH ­ DIGITAL TBC/NR INSERT REC PAUSE STOP/EJECT MULTI BRAND REMOTE CONTROL UNIT INSTRUCTIONS For Customer Use: Enter below the Model No. Serial No. LPT0604-001A 2 EN Dear Customer, Thank you for purchasing the JVC S-VHS video cassette recorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of your new VCR. CAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Caution on Replaceable lithium battery The battery used in this device may present a fire or chemical burn hazard if mistreated. [. . . ] The VCR Plus+ timer programing system eliminates the need to input channel, date, start and stop time data when programing timer recording settings. Simply key in the PlusCode number for the TV broadcast you wish to record and the VCR's timer will be automatically programed. (The PlusCode programing numbers are the numbers next to the program in most TV listing. ) VCR Plus+® Timer Programing Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. 1 Load a cassette POWER 1 4 2 5 8 0 3 2 Make sure the record safety tab is intact. You can also record onto a cassette without a record safety tab by covering the hole with adhesive tape before inserting the cassette. 6 9 4 DAILY CANCEL STOP +/­ 34 WEEKLY 2 Access PlusCode No. The clock must be set to access the PRESS NUMBER KEY (0­9) PlusCode No. PRESS (+/­) TO SET If you have not set the EXPRESS PROGRAMMING PRESS (PROG. ) TO END clock, the Main Menu screen appears after an error message is displayed. Refer to page 8 for the Plug & Play setting or page 10 for the clock setting procedure. 7 8 4 6 27 1 3 4 347 3 Enter PlusCode number PLUSCODE NO. Press the appropriate Number keys to input the PlusCode number printed in the TV listings for the TV broadcast you wish to record, then press OK. 123 PRESS NUMBER KEY (0­9) THEN (OK) PRESS (PROG. ) TO END Then; If the Guide Channel Set screen appears -- go to step 4. To make corrections, press CANCEL and input the correct PlusCode number. EN 29 4 Input receiving channel number The guide channel GUIDE CHANNEL SET number, which is GUIDE CH: 12 assigned to the TV or VCR CH : ­ ­ ­ cable station for the PlusCode number that PRESS NUMBER KEY (0­9) you entered in step 3, OR (5, ), THEN (OK) PRESS (PROG. ) TO END will appear automatically on the Guide Channel Set screen. Press the Number keys (or CH +/­ or SHUTTLE PLUS %fi) to input the number of the channel on which the broadcast for the PlusCode number is received on the VCR, then press OK. The Guide Channel Set screen appears only when you input the PlusCode number of a station for which the guide channel number has not been set previously. If you receive your channels through a cable box, select the cable box output channel -- the channel on which you view the cable box programs on the TV. 7 Return to normal screen Press PROG. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. · If "PROGRAM NOT COMPLETED PROGRAM OVERLAP" appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking. See "When programs overlap each other" on page 36. 8 Engage timer recording standby mode Press TIMER. The VCR turns off automatically and "" is displayed on the front display panel. To use the VCR while it is in timer recording standby mode Press TIMER to cancel the timer recording standby mode, then press POWER to turn on the VCR. DO NOT forget to put the VCR into timer recording standby mode again by pressing TIMER after you use the VCR; otherwise, you cannot record the broadcasts you want. 37, 38) , the timer recording standby mode is automatically engaged when the VCR is turned off. You do not have to press TIMER to engage or disengage the timer recording standby mode. 5 Check program date The PlusCode number you entered and the corresponding timer PROGRAM 1 (PLUSCODE NO. 12345678) recording program is START STOP displayed on the 8:00PM = 10:00PM DATE CH Program screen. Check 12/24/00 12 SP SUN to make sure it is PRESS (8=DAILY, 9=WEEKLY accurate. STOP+/­ = STOP TIME, SP/EP) PRESS (PROG. ) TO END To change the stop time, press STOP +/­. [. . . ] When I pause and then resume a recording, the end of the recording before the pause is overlapped by the new recording. Can I program the timer while I'm watching a tape or a TV broadcast?Yes, but while you are setting the timer you will not see the tape's or broadcast program's picture as it is replaced by the on-screen menu. (The sound from the tape or broadcast program will be heard during the timer setting. ) 58 EN List of terms This guide serves as a quick way to locate frequently used terms and on-screen display names. INDEX A Accidental erasure prevention 20 AUDIO MONITOR 40 Audio Monitor 17 Auto Daylight Saving Time 11 AUTO SP = EP TIMER 39 AUTO TIMER 38 Automatic tracking 17 M Manual tracking 17 Mode lock 15, 16, 20, 21, 23, 25 Multi-Brand Remote Setting cable box brand 51 Setting DBS receiver brand 52 Setting TV brand 50 T Tape speed 19, 42 Time counter 16, 20 Time zone selection 11 Timer recording Canceling 35 Changing 35 Checking 35 Express 32 Guide channel setting 30 VCR Plus+ 28 Timer warning display 34 Tracking 17 Troubleshooting 54 Tuner setting Adding channels 14 Auto Channel Set 13 Deleting channels 14 Manual Channel Set 14 B Basic connections AV connection 6 RF connection 6 S-video connection 6 N Next Function Memory 17 O ON SCREEN (PLAY) 39 ON SCREEN (REC) 38 On-screen display 21 C Channel No. [. . . ]