User manual JVC RX-E5S

[. . . ] HOME CINEMA CONTROL CENTER RX-E5S INSTRUCTIONS LVT1141-003B [B] Warnings, Cautions and Others IMPORTANT for the U. K. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. [. . . ] To use the numeric buttons to operate your target source, press the corresponding source selecting button before operation; otherwise, the remote control may not work as you intend. Selecting the main or sub channel --DUAL MONO You can select the playback sound (channel) you want while playing digital software recorded (or broadcast) in Dual Mono mode (see page 30), which includes two monaural channels separately. Basic settings D MONO: SUB Select to play back the sub-channel (Ch 2). * Signal indicator "R" lights up while playing back this channel. Select to play back the main channel (Ch 1). * Signal indicator "L" lights up while playing back this channel. Select to play back both the main and subchannels (Ch 1/Ch 2). * Signal indicators "L" and "R" light up while playing back these channels. D MONO:MAIN D MONO: ALL Initial setting: D MONO:MAIN * Dual Mono signals can be heard from the following speakers--L (left front speaker), R (right front speaker), and C (center speaker), with respect to the current Surround setting: With Surround Activated Dual Mono setting Without Surround L SUB MAIN ALL Ch 2 Ch 1 Ch 1 R Ch 2 Ch 1 Ch 2 L Center speaker setting SML/LRG C Ch 2 Ch 1 Ch 1+Ch 2 R L Ch 2 Ch 1 NO R Ch 2 Ch 1 Ch 1+Ch 2 Ch 1+Ch 2 NOTE The Dual Mono format is not identical with bilingual broadcasting for TV programs. So this setting does not take effect while watching such bilingual programs. 18 Setting the digital input (DIGITAL IN) terminals--DIGITAL IN1/2 When you use the digital input terminals, register what components are connected to which terminals--DIGITAL IN1/2 (see page 9) so that the correct source name will appear when you select the digital source. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE PL ATT LPCM LCR HP DOLBY D S . WFR LFE NEO : 6 MHz DSP 3D DTS AAC LS SB RS AUTO SR kHz 96 / 24 NOTES This function does not take effect in the following cases: While playing an analogue source, While selecting any of DSP modes (see page 31), or one of the fixed digital decode mode--"DGTL D. D. " or "DGTL DTS" (see page 11), and While listening with the headphones. If you press SURROUND with Auto Surround activated, Auto Surround will be canceled temporarily for the currently selected source. Auto Surround setting will be restored in the following cases: When you turn the receiver off and on, When you change the source, When you change the analogue/digital input, and When you select "AUTO SR: ON" again. DVR/DVD VIDEO VCR (Back to the beginning) TV For DIGITAL IN 2(VIDEO) terminal: EQ C. TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE PL ATT LPCM LCR HP DOLBY D S . WFR LFE NEO : 6 MHz DSP 3D DTS AAC LS SB RS AUTO SR kHz 96 / 24 Setting the Auto Function mode --AUTO MODE The source will be selected automatically simply by turning on a video component. This function takes effect for the video components connected to the receiver using the SCART cable--DVR/DVD and VCR. Auto Function mode works as follows: When a video component is turned on, the receiver selects the video component as the source (and the TV input is changed automatically). When a video component currently selected as the source is turned off, the receiver changes the source to the video source previously selected--DVR/DVD, VCR, or VIDEO. MODE: AUTO1 Auto Function mode works when the receiver is turned on or when TV Direct is activated VIDEO* VCR* TV* (Back to the beginning) DVR/DVD* * The one selected for "DIGITAL IN1" will be skipped. VIDEO VCR TV For the component connected to the VIDEO IN jack on the rear of the receiver. For TV. Initial setting: DVR/DVD (for "DIGITAL IN1") VIDEO (for "DIGITAL IN2") MODE: AUTO2 Setting Auto Surround--AUTO SURRND You can enjoy the Surround mode simply by selecting the source (with digital input selected for that source). Auto Surround also works when the input mode changes from analogue to digital. If a multi-channel signal comes in, an appropriate Surround mode will be turned on. If a Dolby Digital 2-channel or DTS 2-channel signal with surround signal comes in, "PLII MOVIE" will be selected. If a Dolby Digital 2-channel or DTS 2-channel signal without surround signal comes in, "SURRND OFF (stereo)" will be selected. Initial setting: AUTO SR:OFF MODE:MANUAL You need to select the source manually. Initial setting: MODE:MANUAL When "MODE: AUTO1" or "MODE: AUTO2" is selected, the AUTO MODE indicator lights up on the display. [. . . ] If they are changed, this remote control cannot operate the equipment. 37 Operating other manufacturers' products Changing the transmittable signals for operating an STB Set the mode selector to "AUDIO/TV/VCR/STB. " Manufacturers' codes for STB Manufacturer JVC Amstrad BT Canal Stellite Canal + DBox Echostar Finlux Force Galaxis Grundig Hirschmann ITT Nokia Jerrold Kathrein Luxor Mascom Maspro Nokia Pace Panasonic Philips RFT Saba Sagem Salora Selector Skymaster Thomson TPS Triax Videoway Wisi Initial setting: 01 Codes 01, 02 03, 04, 05, 06, 33 01 22 22 26 19, 20, 21, 23 11 30 29 07, 08 07, 19, 39 11 16 13, 14, 36 11 34 13 26, 28, 35 10, 27, 33 15 09, 25 12 37 24, 31 11 31 12, 38 37 24 32 17, 18 07 1 Press and hold STB 2 Press STB CONTROL. . 3 Enter the manufacturer's code using buttons 1 9, and 0. See "Manufacturers' codes for STB" on the right column. 4 Release STB . Now, you can perform the following operation on the STB. STB : Turn on or off the STB. After pressing STB CONTROL, you can perform the following operations on the STB. Select the channel numbers on the STB. See the instructions supplied with the STB for details. 5 Try to operate your STB by pressing STB . When your STB turns on or off, you have entered the correct code. If more than one code is listed for your brand of STB, try each one until the correct one is entered. Manufacturers' codes are subject to change without notice. [. . . ]