User manual JVC RX-DV3R

[. . . ] HOME CINEMA DVD/CD CONTROL CENTER RX-DV3RSL REMOTE CONTROL RM-SRXDV3R STANDBY/ON STB TV TV DIRECT VCR TAPE TV CDR AUDIO FM/AM STB REW/( SLEEP VCR TUNING FM MODE DVD 9/FF TV/VIDEO REPEAT STROBE TV/STB CH SOUND ANALOG /DIGITAL EFFECT CENTER 1 TEST INPUT 2 REAR·L 3 RX-DV3R HOME CINEMA DVD/CD CONTROL CENTER 6 DVD STB VCR TV TAPE/CDR SOURCE NAME FM/AM TV DIRECT 4 7 5 REAR·R AUDIO SURR ON/OFF MASTER VOLUME 8 +10 100+ 9 STANDBY/ON STANDBY SUBTITLE SURR MODE ­ SUBWOOFER + 10/0 ANGLE DIMMER VFP PROGRESSIVE TV RETURN + ZOOM MUTING TV VOL + VOLUME ­ TOP MENU ( PTY ­ MENU PTY 9 DIGEST TA/NEWS/INFO INPUT SURROUND MODE ANALOG/DIGITAL ON/OFF SETTING ADJUST MEMORY COMPACT PTY SEARCH ENTER CHOICE CONTROL SUPER VIDEO INPUT ATT. ON SCREEN RETURN DISPLAY REC MODE DVD/SUPER VCD/VCD/CD HOME CINEMA DVD/CD CONTROL CENTER INSTRUCTIONS LVT0875-009A [B] Warnings, Cautions and Others IMPORTANT for the U. K. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. [. . . ] The DAP mode can reproduce a realistic sound field by adding these indirect sounds. DAP modes can be used when the front and rear speakers are connected to this unit (without respect to the center speaker connection: no sound comes out of the center speaker even if it is connected). Dolby Digital* Used to reproduce multichannel sound tracks of the software encoded with Dolby Digital ( ). · To enjoy the software encoded with Dolby Digital, connect the source component using the digital terminal on the rear of this unit. (See page 8. ) DIGITAL Dolby Digital 5. 1-channel encoding method (so-called discrete multichannel digital audio format) records and digitally compresses the left front channel, right front channel, center channel, left rear channel, right rear channel, and LFE channel signals. Since each channel is completely independent from the other channel signals to avoid interference, you can obtain much better sound quality with much stereo and surround effects. Note: · Dolby Digital or DTS software can be roughly grouped into two categories --multichannel (up to 5. 1-channel) and 2-channel software. To enjoy surround sounds while playing Dolby Digital 2-channel or DTS software, you can use Dolby Pro Logic II. * Manufactured under license from Dolby Laboratories. "Dolby, " "Pro Logic, " and the double-D symbol are trademarks of Dolby Laboratories. **Manufactured underlicense from Digital Theater Systems, Inc. "DTS" and "DTS Digital Surround" are trademarks of Digital Theater Systems, Inc. All rights reserved. 29 Realistic Sound Fields The following DAP modes are provided for this unit: LIVE CLUB : Gives the feeling of a live music club with a low ceiling. : Gives the spacious feeling of a pavilion with a high ceiling. I All Channel Stereo This mode can reproduce a larger stereo sound field using all the connected (and activated) speakers. All Channel Stereo can be used when the front and rear speakers are connected to this receiver without respect to the center speaker connection. If the center speaker is connected and activated, the same phases of the front left and right signals are mixed and output through the center speaker. All Channel Stereo can be used while reproducing 2-channel stereo software, either analog or Linear PCM digital signal. · When All Channel Stereo is selected, the DSP indicator lights up on the display. All Channel Stereo reproduction DANCE CLUB : Gives a throbbing bass beat. HALL PAVILION These DAP modes can be used to add the acoustic surround effects while reproducing 2-channel stereo software, either analog or Linear PCM digital signal, and can give you a real "being there" feeling. · When one of the DAP modes is selected, the DSP indicator lights up on the display. Creating sound field Reflections from behind Early reflections Sound reproduced from normal stereo Direct sounds Sound reproduced from All Channel Stereo Available Surround modes for each input signal Modes Signals Dolby Digital (Multichannel) Dolby Digital (2-channel) Dolby Surround (matrix 2-ch) DTS Digital Surround (Multichannel) DTS Digital Surround (2-channel) Linear PCM Analog STEREO DOLBY DIGITAL DTS SURROUND PL II MOVIE PL II MUSIC LIVE CLUB DANCE CLUB : Possible HALL PAVILION : Impossible ALL CH ST. 30 Creating Realistic Sound Fields Activating Surround Mode When Auto Surround is set to "OFF" or 2-channel source other than Dolby Surround software is played back, activate Surround mode manually. Make sure that you have set the speakers information correctly (see page 24 or 55). · If only front speakers are connected, you cannot activate any Surround mode. On the front panel: Selecting Surround Modes When 2-channel source is played back with Surround mode activated, you can select another Surround mode. Available Surround modes will vary depending on the number of the connected speakers and the playback sound. Make sure that you have set the speaker information correctly (see page 24 or 55). [. . . ] Audio language is different from the one you have selected as your initial audio language. Enter your password to change the parental level (see pages 57 and 58). If this happens, press SUBTITLE on the remote control after starting play (see page 39). Some discs are programed to always use the original language initially. [. . . ]