User manual JVC RX-D211SJ-RX-D211 Instruction Manual

[. . . ] AUDIO / VIDEO CONTROL RECEIVER RX-D211S / RX-D212B INSTRUCTIONS For Customer Use: Enter below the Model No. Serial No. LVT1557-001A [J] Warnings, Cautions, and Others Mises en garde, précautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION Changes or modifications not approved by JVC could void the user's authority to operate the equipment. ATTENTION Des changements ou modifications non approuvés par JVC pourront invalider l'autorité de l'utilisateur à opérer cet appareil. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] · When "SURROUND SPK" is set to "SML (small), " you cannot select "LRG (large)" for the surround back speaker. · When "SURROUND SPK" is set to "NO, " the surround back speaker is fixed to "NO. " · When "S BACK SPK" is set to "NO, " you cannot select "S BACK OUT. " · When "SB OUT" is set to "<1SPK>, " connect the surround back speaker to the left surround back speaker terminal (see page 6). No sound comes from the surround back speaker if you connect it to the right surround back speaker terminal. 3 Press SET. The current setting of the selected item appears. ANALOG L S. WFR R 4 Turn MULTI JOG to select the appropriate setting. ANALOG L S. WFR R DVR/DVD TV Your setting is stored. DBS VCR 5 Press SET. 6 Repeat steps 2 to 5 to set other items if necessary. 7 Press SETTING. The source indication resumes on the display. 22 Setting the speaker distance The distance from your listening point to the speakers is one of the important elements to obtain the best possible sound effect from the Surround/DSP modes. By referring to the speaker distance, the receiver automatically sets the delay time of the sound through each speaker so that sounds through all the speakers can reach you at the same time. D UNIT <feet> Select to set the distance in feet. Activating the EX/ES/PLIIx setting-- EX/ES/PLIIx Depending on this setting, available Surround modes for digital multi-channel software vary--EX/ES/PLIIx reproduction or 5. 1channel reproduction. · For details about relation between EX/ES/PLIIx setting and available Surround mode, see page 33. · To activate the Surround mode, see page 34. <AUTO> Initial setting: D UNIT <meter> 7 Speaker distance-- FRONT L DIST (for the left front speaker), FRONT R DIST (for the right front speaker), CENTER DIST (for the center speaker), SURR L DIST (for the left surround speaker), SURR R DIST (for the right surround speaker), S BACK L DIST (for the left surround back speaker), S BACK R DIST (for the right surround back speaker) Adjustable range: 0. 3 m to 9. 0 m in 0. 3 m intervals (1 ft to 30 ft in 1 ft intervals) Initial setting: 3. 0 m (10 ft) for all speakers According to the incoming signal, an appropriate Surround mode is applied. · For Dolby Digital Surround EX and DTS-ES software, 7. 1-channel reproduction is applied*. · For other multi-channel (4 channel or more) encoded software, 5. 1-channel reproduction is applied. Select to apply 7. 1-channel reproduction to both 5. 1-channel and 6. 1-channel encoded software. both 5. 1-channel and 6. 1-channel encoded software. <ON> <PLIIx MOVIE> Select to apply PLIIx MOVIE reproduction to <PLIIx MUSIC> Select to apply PLIIx MUSIC reproduction to both 5. 1-channel and 6. 1-channel encoded software. <OFF> C L R 3. 3 m (11 ft) 3. 0 m (10 ft) 2. 7 m (9 ft) 2. 4 m (8 ft) 2. 1 m (7 ft) Select to cancel the EX/ES/PLIIx reproduction. Initial setting: <AUTO> * For some Dolby Digital Surround EX software, Dolby Digital 5. 1channel reproduction ("DOLBY DIGITAL") may be applied even though you have selected "<AUTO>. " In this case, select "<ON>" to apply "DOLBY D EX. " NOTES · When "SURROUND SPK" is set to "NO" (see page 22), this function is not available. · When "S BACK SPK" is set to "NO" (see page 22), the Virtual Surround Back (see page 33) is applied for EX/ES/PLIIx reproduction. LS RS SBL SBR In this case, set the distance as follows: Left front speaker (L): "FRONT L <3. 0m> (10ft)" Right front speaker (R): "FRONT R <3. 0m> (10ft)" Center speaker (C): "CENTER <3. 0m> (10ft)" Left surround speaker (LS): "SURR L <2. 7m> (9ft)" Right surround speaker (RS): "SURR R <2. 7m> (9ft)" Left surround back speaker (SBL) : "SBACK L <2. 4m> (8ft)" Right surround back speaker (SBR) : "SBACK R <2. 4m> (8ft)" NOTES · You cannot set the speaker distance for the speakers you have set to "NO. " · If you have selected "<1SPK>" for "S BACK OUT" (see page 22), "S BACK DIST" appears instead of "S BACK L DIST" and "S BACK R DIST. " 23 Selecting the main or sub channel --DUAL MONO You can select the playback sound (channel) you want while playing digital software recorded (or broadcasted) in Dual Mono mode (see page 31), which includes two monaural channels separately. When the receiver detects Dual mono signals, the DUAL MONO indicator lights up on the display. D MONO <MAIN> Select to play back the main channel (Ch 1). * Signal indicator "L" lights up while playing back this channel. D MONO <SUB> Select to play back the sub-channel (Ch 2). * Signal indicator "R" lights up while playing back this channel. D MONO <ALL> Select to play back both the main and subchannels (Ch 1/Ch 2). * Signal indicators "L" and "R" light up while playing back these channels. Initial setting: D MONO <MAIN> * Dual Mono signals can be heard from the following speakers--L (left front speaker), R (right front speaker), and C (center speaker), with respect to the current Surround setting: With Surround Activated Dual Mono setting Without Surround L MAIN SUB ALL NOTE The Dual Mono format is not identical with bilingual broadcasting for TV programs. So this setting does not take effect while watching such bilingual programs. Ch 1 Ch 2 Ch 1 R Ch 1 Ch 2 Ch 2 L Center speaker setting SML/LRG C Ch 1 Ch 2 Ch 1+Ch 2 R L Ch 1 Ch 2 NO R Ch1 Ch 2 Setting the crossover frequency--CROSSOVER Small speakers cannot reproduce the bass sounds efficiently. If you use a small speaker in any position, this receiver automatically reallocates the bass sound elements assigned to the small speaker to the large speakers. To use this function properly, set this crossover frequency level according to the size of the small speaker connected. [. . . ] If they are changed, this remote control cannot operate the equipment. Codes 01 02 03, 04 05 06 07 08, 09 10 06 11 12 12 13 14 05 15 05, 16 Manufacturers' codes for DBS tuner Manufacturer Echostar G. I. Hitachi Hughes Panasonic Primestar RCA Sony Toshiba Initial setting: 01 Codes 40 41 42 43 44 45 46 47 48 41 Troubleshooting Use this chart to help you solve daily operational problems. If there are any problems you cannot solve, contact your JVC's service center. PROBLEM The power does not come on. The receiver turns off (enters standby mode). POSSIBLE CAUSE The power cord is not plugged in. [. . . ]