User manual JVC RX-668R

[. . . ] AUDIO/VIDEO CONTROL RECEIVER AUDIO/VIDEO-RECEIVER MIT STEUEREINHEIT AMPLI/TUNER DE COMMANDE AUDIO/VIDEO GEINTEGREERDE AUDIO/VIDEO-VERSTERKER RECEPTOR DE CONTROL DE AUDIO/VÍDEO RICEVITORE DI CONTROLLO AUDIO/VIDEO RX-668RBK SOUND CONTROL /I TV VCR AUDIO ON SCREEN SET EXIT CD-DISC DELAY TEST SURROUND 1 EFFECT 2 ­ CENTER + 3 6 ­ REAR·L + 4 MENU 5 8 7/P 100+ 9 ­ REAR·R + RETURN +10 VOLUME VCR CH 0 TV VOL. 10 ENTER TV CH MASTER VOLUME SLEEP ONE TOUCH TV/VIDEO OPERATION CD FM/AM RX-668R AUDIO/VIDEO CONTROL RECEIVER ­ TAPE /MD STANDBY + BASS BOOST ADJUST TV D SOUN ON O PH VCR MUTING PTY SEARCH DISPLAY MODE DVD DVD /I LT I STANDBY/ON EON TA/NEWS/INFO SETTING MU RE C PA USE 8 DIS MEMORY PLAY PTY SEARCH DVD MULTI DVD VCR TV SOUND SURROUND PTY ­ + PTY ONE TOUCH OPERATION SPEAKERS CD PHONO TAPE/MD FM/AM INPUT ATT. TEXT DISPLAY PHONES 1 2 SOURCE NAME _ ON -- OFF RM-SR668RU REMOTE CONTROL ENHANCED COMPULINK CONTROL SYSTEM INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES ISTRUZIONI For Customer Use: Enter below the Model No. Serial No. LVT0142-004A [E] Warnings, Cautions and Others/Warnung, Achtung und sonstige Hinweise/ Mises en garde, précautions et indications diverses/Waarschuwingen, voorzorgen en andere mededelingen/Avisos, precauciones y otras notas/ Avvertenze e precauzioni da osservare Caution ­­ STANDBY/ON switch!The STANDBY/ON switch in any position does not disconnect the mains line. Den Netzstecker aus der Steckdose ziehen, um die Stromversorgung vollkommen zu unterbrechen. [. . . ] HALL: PAVILION: As for the DVD MULTI playback mode, see page 22. Early reflections Direct sounds * Manufactured under license from Dolby Laboratories Licensing Corporation. "Dolby, " the double-D symbol, and "Pro Logic" are trademarks of Dolby Laboratories Licensing Corporation. 17 Available DSP Modes According to the Speaker Arrangement Available DSP modes will vary depending on how many speakers are used with this receiver. Make sure that you have set the speaker information correctly (see page 11). Speaker arrangements Available DSP modes Each time you press SURROUND, the DSP modes change as follows: · · · · · · · 3D THEATER LIVE CLUB DANCE CLUB HALL PAVILION 3D ACTION OFF (DSP mode is canceled) Front speaker TV Front speaker Front speaker TV Center speaker Front speaker Each time you press SURROUND, the DSP modes change as follows: · · · · · · · · * Though "3 stereo" is selected, DOLBY (3 Stereo)* "PRO LOGIC" appears on the 3D THEATER display. LIVE CLUB DANCE CLUB HALL PAVILION 3D ACTION OFF (DSP mode is canceled) Front speaker TV Front speaker Each time you press SURROUND, the DSP modes change as follows: · · · · · · · · DOLBY (PRO LOGIC) THEATER LIVE CLUB DANCE CLUB HALL PAVILION 3D ACTION OFF (DSP mode is canceled) Rear speaker Rear speaker Front speaker TV Center speaker Front speaker Each time you press SURROUND, the DSP modes change as follows: · · · · · · · · DOLBY (PRO LOGIC) THEATER LIVE CLUB DANCE CLUB HALL PAVILION 3D ACTION OFF (DSP mode is canceled) Rear speaker Rear speaker 18 English English Adjusting the 3D-PHONIC Modes Before you start, remember. . . · Make sure that you have set the speaker information correctly (see page 11). If the setting is canceled before you finish, start from step 1 again. Adjusting DAP Modes Before you start, remember. . . · Make sure that you have set the speaker information correctly (see page 11). If the setting is canceled before you finish, start from step 1 again. · You can only adjust the rear speaker output level when you have connected the rear speakers and have set "REAR SPK" to "YES. " See page 11. On the front panel: 1. Press SURROUND repeatedly until "3D ACTION" or "3D THEATER, " appears on the display. SURROUND On the front panel: The 3D-PHONIC, DSP, PRO LOGIC and the selected 3DPHONIC mode indicators also light up on the display. 2. Press ADJUST so that the cursor control % / fi / @ / # buttons work for adjusting the surround setting. Press cursor control % / fi repeatedly until "DSP EFFECT" appears on the display. Press cursor control @ / # to select an effect level you want. · Each time you press the button, the effect level changes as follows: ADJUST 1. Press SURROUND repeatedly until the DAP mode -- LIVE CLUB, DANCE CLUB, HALL, or PAVILION -- appears on the display. SURROUND The DSP and the selected DAP mode indicators also light up on the display. 2. Press ADJUST so that the cursor control % / fi / @ / # buttons work for adjusting the DSP setting. Press cursor control % / fi repeatedly until "REAR LEVEL" appears on the display. ADJUST DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3 DSP EFFECT 5 DSP EFFECT 4 As the number increases, the selected 3D-PHONIC mode becomes stronger. 4. Press cursor control @ / # to adjust the rear speaker output level (from ­10 to +10). Note: You cannot adjust the left and right rear speaker output levels separately. From the remote control: SOUND CONTROL 1. Press SOUND CONTROL. The 10 keys are activated for sound adjustments. 2. Press SURROUND repeatedly until "3D ACTION" or "3D THEATER" appears on the display. SURROUND 3 5. Press cursor control % / fi repeatedly until "DSP EFFECT" appears on the display. The 3D-PHONIC, DSP, PRO LOGIC and the selected 3DPHONIC mode indicators also light up on the display. 6. Press cursor control @ / # to select an effect level you want. · Each time you press the button, the effect level changes as follows: 3. [. . . ] To release it, press 3. EFFECT 2 ­ CENTER + 4 MENU 5 8 6 ­ REAR·L + 7/P 9 ­ REAR·R + RETURN 10 Note: ENTER For detailed menu operations, refer to the instructions supplied with the discs or the DVD player. Note: To operate the cassette deck or MD recorder using the COMPU LINK remote control system, set the source name correctly. (See page 11. ) TV You can always perform the following operations: TV : TV VOL. Changes the channels. IMPORTANT: To operate JVC's video components using this remote control: · Aim the remote control directly at the remote sensor on the VCR, DVD player or TV, not on the receiver. · Some JVC VCRs can accept two types of the control signals -- remote code "A" and "B. " Before using this remote control, make sure that the remote control code of the VCR connected to the VCR jacks is set to code "A. " After pressing TV SOUND, you can perform the following operations on a TV: 1 ­ 9, 0, 100+: Selects the channels. [. . . ]