User manual JVC RX-558R

[. . . ] FM/MW/LW RECEIVER UKW/MW/LW-RECEIVER AMPLI/TUNER FM/PO/GO FM/MG/LG TUNER/VERSTERKER RECEPTOR FM/MW/LW RICEVITORE MF/OM/OL RX-558RBK CD TV VCR AUDIO TAPE/MD DELAY TEST SURROUND 1 FM/AM EFFECT 25 5 8 5 3 5 CENTER + 4 VCR 5 6 REARL + 7/P DVD SOUND CONTROL 9 MENU REARR + 10 DVD MULTI CD-DISC TV VOL. +10 ENT PHONO TV/VIDEO TV CH + RX-558R FM/MW/LW RECEIVER MASTER VOLUME ONE TOUCH OPERATION + STANDBY BASS BOOST ADJUST + + MUTING + VCR CH PTY SEARCH DISPLAY MODE VOLUME /I ECN STANDBY/ON TA/NEWS/INFO SETTING SLEEP PTY SEARCH MEMORY 8 4 1 PTY 7 DISPLAY + PTY 4 1 DVD MULTI DVD VCR FM SURROUND ONE TOUCH OPERATION RM-SR558RU REMOTE CONTROL SPEAKERS PHONES CD PHONO TAPE/MD AM INPUT ATT. 1 2 SOURCE NAME _ ON -- OFF ENHANCED COMPULINK CONTROL SYSTEM INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES ISTRUZIONI For Customer Use: Enter below the Model No. Serial No. LVT0141-004A [E] Warnings, Cautions and Others/Warnung, Achtung und sonstige Hinweise/ Mises en garde, prcautions et indications diverses/Waarschuwingen, voorzorgen en andere mededelingen/Avisos, precauciones y otras notas/ Avvertenze e precauzioni da osservare Caution STANDBY/ON switch!The STANDBY/ON switch in any position does not disconnect the mains line. Den Netzstecker aus der Steckdose ziehen, um die Stromversorgung vollkommen zu unterbrechen. [. . . ] Press cursor control @ / # to select a preset channel station. Pressing @ decreases the preset channel number. Pressing # increases the preset channel number. To store the preset stations Before you start, remember. . . If the setting is canceled before you finish, start from step 1 again. From the remote control: 1. Each time you press the button, the band alternates between FM and AM (MW/LW). FM/AM On the front panel ONLY: 1. Tune in the station you want to preset (see above). If you want to store the FM reception mode for this station, select the FM reception mode you want. Press the 10 keys to select a preset channel number. For channel number 5, press 5. For channel number 30, press +10, +10, then 10. DELAY TEST SURROUND 1 EFFECT 25 5 3 5 CENTER + 4 5 6 REARL + 7/P 8 2. Press MEMORY. "CH-" appears and the channel number position starts flashing on the display for about 5 seconds. MEMORY REARR + 10 Note: When you use the 10 keys on the remote control, be sure that they are activated for the tuner, not for the CD and others. Press cursor control @ / # to select a channel number while the channel number position is flashing. 13 5 9 MENU +10 ENT Selecting the FM Reception Mode When an FM stereo broadcast is hard to receive or noisy You can change the FM reception mode while receiving an FM broadcast. What Information Can RDS Signals Provide? You can see the RDS signals the station sends on the display. To show the RDS signals Press DISPLAY MODE on the front panel (or DISPLAY on the remote control) while listening to an FM station. PTY SEARCH DISPLAY MODE On the front panel ONLY: 1. The cursor control % / fi / @ / # buttons can be now used for operating the tuner. FM 4 1 PTY 7 DISPLAY + PTY 4 1 On the front panel On the remote 2. Press cursor control % / fi repeatedly until "FM MODE" appears on the display. Press cursor control @ / # to switch the FM reception "FM AUTO" or "FM MONO. " Each time you press the button, the display changes to show you the following information: PS Frequency PTY RT FM AUTO: When a program is broadcasted in stereo, you will hear stereo sound; when in monaural, you will hear monaural sounds. FM MONO: Reception will be improved although you will lose the stereo effect. The MUTE AUTO indicator goes off on the display. PS (Program Service): While searching, "PS" appears and then the station names will be displayed. PTY (Program Type): While searching, "PTY" appears and then the type of the broadcast program will be displayed. RT (Radio Text): While searching, "RT" appears and then text messages the station sends will be displayed. Frequency: Station frequency (non-RDS service) Using the RDS (Radio Data System) to Receive FM Stations RDS allows FM stations to send an additional signal along with their regular program signals. For example, the stations send their station names, as well as information about what type of program they broadcast, such as sports or music, etc. When tuned to an FM station which provides the RDS service, the RDS indicator lights up on the display. With the receiver, you can receive the following types of RDS signals. PS (Program Service) : shows commonly known station names PTY (Program Type) : shows types of broadcast programs RT (Radio Text) : shows text messages the station sends EON (Enhanced Other Network): see page 16. About characters shown on the display When the display shows PS, PTY, or RT signals, the following characters are used. [. . . ] To release it, press 3. DVD player After pressing DVD or DVD MULTI, you can perform the following operations on a DVD player: 3: 4: : 7: 8: Starts playing. To release it, press 3. Note: To operate the cassette deck or MD recorder using the COMPU LINK remote control system, set the source name correctly. (See page 11. ) After pressing DVD or DVD MULTI, these buttons can be used for the DVD menu operations. TEST MD recorder After pressing TAPE/MD, you can perform the following operations on the MD recorder: 3: 4: : 7: 8: Starts playing. To release it, press 3. EFFECT 25 CENTER + 5 4 5 8 5 5 6 REARL + 7/P 9 MENU REARR + Note: To operate the cassette deck or MD recorder using the COMPU LINK remote control system, set the source name correctly. [. . . ]