User manual JVC RX-5060 Instruction Manual

[. . . ] AUDIO/VIDEO CONTROL RECEIVER RX-5060B TA/NEWS/INFO DISPLAY MODE INSTRUCTIONS For Customer Use: Enter below the Model No. Serial No. LVT1507-001A [J] Warnings, Cautions and Others/ Mises en garde, prcautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN For U. S. A This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] 7 Press EXIT. The source indication resumes on the display. 17 English Basic Settings English Setting the Speakers To obtain the best possible surround effect from the Surround and DSP modes, register the setting about the speaker arrangement after all connections are completed. If you have used Quick Speaker Setup on page 16, this setting is not required. Subwoofer setting--SUBWOOFER Select whether you have connected a subwoofer or not. SUBWOOFER NO: Select when no subwoofer is used. Speaker distance--FRONT L DIST, FRONT R DIST, CENTER DIST, SURR L DIST, SURR R DIST Set the distance from the listening point within the range of 0. 3 m (1 ft) to 9. 0 m (30 ft), in 0. 3 m (1 ft) intervals. When shipped from the factory, distance for each speaker is set to "3. 0m (10FT). " Note: You cannot set the speaker distance for the speakers you have selected "NONE. " C L R 3. 3 m (11 ft) 3. 0 m (10 ft) 2. 7 m (9 ft) 2. 4 m (8 ft) 2. 1 m (7 ft) Note: If you have selected "SUBWOOFER NO" for the subwoofer, you cannot use the SUBWOOFER OUT ON/OFF button on the front panel. Speaker size--FRNT SPEAKERS, CNTR SPEAKER, SURR SPEAKERS Select the size for each connected speaker. In the above case, set the speaker distance as follows: Front speakers: Center speaker: Surround speakers: 3. 0m (10FT) 3. 0m (10FT) 2. 7m (9FT) Notes: Keep the following comments in mind as reference when adjusting. If the size of the cone speaker unit built in your speaker is larger than 12 cm, select "LARGE, " and if it is smaller than 12 cm, select "SMALL. " If you have selected "SUBWOOFER NO" for the subwoofer setting, you can only select "LARGE" for the front speakers. If you have selected "SMALL" for the front speakers, you cannot select "LARGE" for the center and surround speakers. Setting the Bass Sounds You can adjust subwoofer and bass sounds precisely according to your preference. Subwoofer output--SUBWOOFER OUT The subwoofer emits the LFE signals* and the bass elements of each speaker set to "SMALL. " You can make the bass elements of the front speaker channels (MAIN) emitted through the subwoofer. Select one of the following: SWFR LFE: Select to emit the LFE signals and the bass elements of each speaker set to "SMALL. " Setting the Speaker Distance The distance from your listening point to the speakers is another important element to obtain the best possible sound of the Surround and DSP modes. By referring to the speaker distance setting, this unit automatically sets the delay time of the sound through each speaker so that sounds through all the speakers can reach you with the same timing. If you have used Quick Speaker Setup on page 16, this setting is not required. UNIT FEET: Select to set the distance in feet. SWFR LFE+MAIN: Select to emit the bass elements of the front speakers' channels (MAIN) adding to the effect of "SWFR LFE" when no bass elements are emitted through the subwoofer. Notes: When "SUBWOOFER" is set to "SUBWOOFER NO" (see the left column), this function is not available. * The LFE signals are emitted only when playing the following software with the LFE signals: Dolby Digital multi channel software DTS multi channel software When playing an analogue source or a linear PCM software, no LFE signals are emitted. 18 Crossover frequency--CROSSOVER You can select the crossover frequency for the small speakers used. The signals below the preset frequency level will be sent to and be reproduced by the subwoofer (or by "LARGE" speakers when "SUBWOOFER" is set to "SUBWOOFER NO"). Select one of the crossover frequency levels according to the size of the small speaker connected. CROSS 80HZ: Select when the cone speaker unit built in the speaker is about 12 cm. Selecting the Main or Sub Channel You can select the playback sound (channel) you want while playing digital software recorded (or broadcast) in Dual Mono mode (see page 24), which includes two monaural channels separately. MONO MAIN: Select to play back the main channel (Ch 1). * Signal indicator "L" lights up while playing back this channel. MONO SUB: Select to play back the sub-channel (Ch 2). * Signal indicator "R" lights up while playing back this channel. CROSS 100HZ: Select when the cone speaker unit built in the speaker is about 10 cm. CROSS 120HZ: Select when the cone speaker unit built in the speaker is about 8 cm. CROSS 150HZ: Select when the cone speaker unit built in the speaker is about 6 cm. CROSS 200HZ: Select when the cone speaker unit built in the speaker is about 5 cm. MONO ALL: Select to play back both the main and subchannels (Ch 1/Ch 2). * Signal indicators "L" and "R" light up while playing back these channels. Notes: Notes: If you have selected "LARGE" for all activated speakers (see page 18), this function is fixed to "CROSS OFF. " Crossover frequency is not valid for "HEADPHONE" and "3D H PHONE. " The Dual Mono format is not identical with bilingual broadcasting or the MTS (Multichannel Television Sound) format used for TV programs. [. . . ] If your CD changer is of 200-disc loading capability (except for XL-MC100 and XL-MC301), you can do the following operations using the number buttons after pressing CD. Press 3 to start playback. DVD player You can always perform the following operation: STANDBY/ON DVD: Turn on or off the DVD player. After pressing DVD, you can perform the following operations on the DVD player: 3: 4: : 7: 8: Start playing. To resume, press 3. 2 4 MENU Examples: Selecting disc number 3, track number 2, and starting playback. Press 1, 0, 5, then 1, 2, then 3. After pressing DVD, these buttons can be used for the DVD menu operations. 6 8 Note: For detailed menu operations, refer to the instructions supplied with the discs or the DVD player. 7/P ENTER 10 Note: It is required to press each button within 4 seconds in the above procedure. TV You can always perform the following operations: STANDBY/ON TV: Turn on or off the TV. [. . . ]