User manual JVC RX-5000VBK

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. For U. S. A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Repeat steps 1 to 4 until you store all the stations you want. To erase a stored preset station Storing a new station on a used number erases the previously stored one. 13 EN08-20. RX-5000V[J]/F 13 99. 10. 29, 9:09 AM Selecting the FM Reception Mode To tune in a preset station On the front panel: 1. • The MULTI CURSOR % / fi / @ / # buttons can be now used for operating the tuner. When an FM stereo broadcast is hard to receive or noisy FM AM You can change the FM reception mode while receiving an FM broadcast. On the front panel ONLY: 1. Press MULTI CURSOR % / fi repeatedly until “–PRESET+” appears on the display. Press MULTI CURSOR @ / # to select a preset channel station. • Pressing @ decreases the preset channel number. • Pressing # increases the preset channel number. MULTI CURSOR FM The last station of the selected band is tuned in. • The MULTI CURSOR % / fi / @ / # buttons can be now used for operating the tuner. MULTI CURSOR 2. Press MULTI CURSOR % / fi repeatedly until “FM MODE” appears on the display. MULTI CURSOR From the remote control: 1. • Each time you press the button, the band alternates between FM and AM. FM/AM 3. Press MULTI CURSOR @ / # to switch the FM reception “FM MONO” or “FM AUTO. ” SURROUND MULTI CURSOR 2. Press the 10 keys to select a preset channel number. • • • • For channel number 5, press 5. For channel number 30, press +10, +10, then 10. DELAY TEST 1 EFFECT 25 5 8 5 3 5 – CENTER + 4 5 6 – REAR•L + 7/P 9 MENU – REAR•R + 10 +10 ENT Note: When you use the 10 keys on the remote control, be sure that they are activated for the tuner, not for the CD and others. Speaker arrangements Available DSP modes Each time you press SURROUND, the DSP modes change as follows: • • • • • • • 3D THEATER DANCE C (DANCE CLUB) LIVE C (LIVE CLUB) HALL PAVILION 3D ACTION OFF (DSP mode is canceled) Front speaker TV Front speaker Front speaker TV Center speaker Front speaker Each time you press SURROUND, the DSP modes change as follows: • • • • • • • • 3 STEREO 3D THEATER DANCE C (DANCE CLUB) LIVE C (LIVE CLUB) HALL PAVILION 3D ACTION OFF (DSP mode is canceled) Front speaker TV Front speaker Each time you press SURROUND, the DSP modes change as follows: • • • • • • • • PRO LOGIC THEATER DANCE C (DANCE CLUB) LIVE C (LIVE CLUB) HALL PAVILION 3D ACTION OFF (DSP mode is canceled) Rear speaker Rear speaker Front speaker TV Center speaker Front speaker Each time you press SURROUND, the DSP modes change as follows: • • • • • • • • PRO LOGIC THEATER DANCE C (DANCE CLUB) LIVE C (LIVE CLUB) HALL PAVILION 3D ACTION OFF (DSP mode is canceled) Rear speaker Rear speaker 16 EN08-20. RX-5000V[J]/F 16 99. 10. 29, 9:09 AM Adjusting the 3D-PHONIC Modes Before you start, remember. . . • Make sure that you have set the speaker information correctly (see page 11). If the setting is canceled before you finish, start from step 1 again. Adjusting the DAP Modes Before you start, remember. . . • Make sure that you have set the speaker information correctly (see page 11). If the setting is canceled before you finish, start from step 1 again. • You can only adjust the rear speaker output level when you have connected the rear speakers and have set “REAR SPK” to “YES. ” See page 11. On the front panel: 1. Press SURROUND repeatedly until “3DACTION” or “3D THEATR” appears on the display. SURROUND On the front panel: The 3D-PHONIC, PRO LOGIC indicators also light up on the display. 2. Press ADJUST so that the MULTI CURSOR % / fi / @ / # buttons work for adjusting the surround setting. Press MULTI CURSOR % / fi repeatedly until “–EFFECT+” appears on the display. Press MULTI CURSOR @ / # to select an effect level you want. • Each time you press the button, the effect level changes as follows: ADJUST 1. Press SURROUND repeatedly until the DAP mode — DANCE CLUB, LIVE CLUB, HALL, or PAVILION — appears on the display. The DAP indicator also lights up on the display. SURROUND MULTI CURSOR 2. [. . . ] Enclose, with the unit, a letter stating the problem or symptom that exists and also a copy of the receipt or bill of sale you received when you purchased your JVC unit. Print your home return address on the outside and the inside of the carton. Send to the appropriate JVC Factory Service Center as listed above. Don’t service it yourself. Refer servicing to qualified service personnel. ACCESSORIES To purchase accessories for your JVC product, you may contact your local JVC Dealer. [. . . ]