User manual JVC RX-450LBK SERVICE MANUAL

[. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] Turn the volume down or turn off the receiver for a while and turn it on again. If the receiver turns off soon after doing solutions above, consult your dealer after unplugging the power cord. Check speaker wiring, then reconnect if necessary (see page 6) after unplugging the power cord. Check the audio connections (see pages 7 to 13) after unplugging the power cord. Check speaker wiring and reconnect if necessary (see page 6) after unplugging the power cord. This is not a malfunction. Power "OVER HEAT" flashes on the display, then the receiver turns off. The receiver is overloaded because of high volume or long time usage. No sound from speakers. Speaker signal cables are not connected. Connections are incorrect. Muting is activated. Sound An incorrect input mode (analog or digital) is selected. When you use the digital coaxial connection, the sounds may be intermittently distorted by the outside noise such as a lightning discharge but the sound will be restored automatically. The station is too far away. Sounds are intermittently distorted by the outside noise such as a lightning discharge. Remote control Remote control does not operate as you intend. Remote control does not work. Set the mode selector correctly, then press the corresponding source selecting button before operation. Move the antenna farther from automobile traffic. Tuner The wrong antenna is being used. Déconnectez la fiche d'alimentation secteur pour couper STANDBY/ON, l'alimentation complètement. La touche dans n'importe quelle position, ne déconnecte pas le système du secteur. L'alimentation ne peut pas être télécommandé. For USB wireless transmitter This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may Cause undesired operation. CAUTION: To maintain compliance with FCC's RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations. Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. For Canada/pour le Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. For Canada/pour le Canada Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. L'utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l'utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. For Canada/pour le Canada CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND Parts identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Before Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Select the chapter number. After pressing DBS, you can perform the following operations on the CATV converter or DBS tuner. CHANNEL +/­: 1 ­ 10, 0: Change the channel numbers on the CATV converter or DBS tuner. Select the channel numbers on the CATV converter or DBS tuner. ¢: 7: 8: TOP MENU/MENU: See the instructions supplied with the CATV converter or DBS tuner for details. 5 Try to operate your CATV converter or DBS tuner by pressing DBS/CATV . When your CATV converter or DBS tuner turns on or off, you have entered the correct code. If more than one code is listed for your brand of CATV converter or DBS tuner, try each one until the correct one is entered. See the instructions supplied with the DVD player for details. 6 Try to operate your DVD player by pressing Manufacturers' codes for CATV converter Manufacturer G. I. Atlanta Samsung Tocom Zenith Codes 01 02 03, 04, 05, 06 07, 08, 09, 10, 11, 12, 13, 14, 15 16, 17, 18 19 20, 21, 22 23, 24 25, 26, 27, 28, 29, 30 31, 32 33, 34, 35 36 37 38, 39 DVR/DVD . When your DVD player turns on or off, you have entered the correct code. Manufacturers' codes for DVD player Manufacturer JVC Hitachi Kenwood Magnavox Marantz Mitsubishi Onkyo Panasonic Philips Pioneer Proscan RCA Samsung Sony Toshiba Yamaha Zenith Initial setting: 01 NOTE You cannot use this remote control to operate other manufacturers' DVD recorder. [. . . ]